Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons. Deaths, serious injury or damage to property may occur if the above is not followed exactly. page no. Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Parts List Exploded View Finial 56-01-417 2 Dome 56-01-418 3 Thermal Baffle 56-01-476 4 Ceramic Insulator* 5 Dome Brace 56-01-419 6 Upper Power Cord* 7 Bulb Power Cord* 8 Heat Reflector 56-01-420 9 Bulb Clip (4) 56-01-452 10 Halogen Bulb 56-01-421 11 Heat Reflector Spacer 56-01-422 12 Wire Guard 56-01-423 13 Post Support 56-01-424 14 Post 56-01-484 Upper Body Assembly 56-01-483 15 Shroud Cover* 16 Shroud Gasket (2)* 56-01-480 17 Tip Switch* 18 Shroud Support Bracket* 19 Controller* 20 Inner Shroud Support Pole* 21 Inner Shroud Support Bar* 22 Pin Connector* 23 Inner Shroud Support Bracket* 24 Main Power Cord 56-01-455 25 Corner Shroud Bracket (4)* 26 Side Shroud Panel (3)* 27 Back Shroud Panel* 28 Power Switch Assembly* 56-01-438 29 Restoration Switch Assembly* 56-01-439 30 Fuse (250V, 20A)* 56-01-441 31 Fuse Cap* 32 Fuse Support Bracket* 33 Base 56-01-442 34 Power Cord Bracket* 35 Weight Plate 56-01-454 * Pre-assembled 5 1 2 22 3 16 12 25 6 8 10 14 9 11 15 18 19 24 25 23 16 29 27 28 13 20 26 26 26 32 31 30 33 34 35 7 4 21 17 Hardware Tools Required for Assembly (Not Included) #2 Phillips Head Screwdriver Screw 5/32” x 10 mm Stainless Steel Phillips Truss Head 2 pcs A 3/16” x 10 mm Black Nickel Plated Phillips Truss B Screw 4 pcs Head ® Outdoor Patio Heater Model No. EWT700SP Assembly Instructions 1 2 Attach Post DO NOT RETURN PRODUCT TO STORE. For assistance call 1.800.762.1142 toll free. Please have your owner’s manual and serial number available for reference. For Easiest Assembly: • To avoid losing any small components or hardware, assemble your product on a hard level surface that does not have cracks or openings. • Clear an area large enough to layout all components and hardware. • When applicable, tighten all hardware connections by hand first. Once the step is completed, go back and fully tighten all hardware. • Follow all steps in order to properly assemble your product. Note: Two (2) adults may be required for assembly. 3 Attach Head Assembly 4 Attach Inner Power Cord Contact 1.800.762.1142 for assistance. Do not return to place of purchase. page no. 5 5 Attach Base Assembly and Shroud Gasket Note: Rubber ring must be placed in the round opening in the base. B x 4 6 Attach Power Cord Bracket A x 2 5 Attach Base Assembly and Shroud Gasket Note: Rubber ring must be placed in the round opening in the base. B x 4 6 Attach Power Cord Bracket A x 2 Attach Finial 7 ® Outdoor Patio Heater Model No. EWT700SP NOTE: Heater functions best WITHOUT an extension cord. If an extension cord is necessary: • Use a UL approved, 3 prong plug (grounded) cord shall be no. 14 AWG minimum size and rated not less than 2,000 watts. •Neverconnecttwoormoreextensioncordstogether. • Use the shortest extension cord possible. • Keep connections dry and off the ground. • Avoid draping the electric heater cord where children or animals could encounter it. Before Turning “ON” 1. Make sure all labels, packaging and protective films have been removed from the heater. 2. Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. Turning “ON” 1. Make sure the power button is in the “OFF” position. (Illustration 1) 2. Plug the power cord into a dry GFI (Ground Fault Interrupter) 3 plug outlet. (Illustration 2) 3. Push the power button in the “ON” position. (Illustration 3) 4. Push the restoration button (Illustration 4). This will start the heater. Note: When restarting the halogen bulb will start up slowly before getting to full power. While Heater is “ON” If heater tips over, the heater will automatically turn “OFF”. If heater tips over: 1. IMMEDIATLEY unplug power cord from the wall outlet. 2. Carefully turn the heater upright. CAUTION: Dome, pole and shroud cover may be hot. Use heat resistant gloves to set heater upright. 3. Turn the power button to the “OFF” position. 4. Inspect heater to ensure no damage. If no damage continue to next step. If there is damage call a qualified technician to inspect and make any necessary repairs. Do NOT use the heater if there is any sign of damage. A qualified technician should inspect and make any nescessary repairs before the heater is used again. 5. Plug the power cord into a dry GFI (Ground Fault Interrupter) 3 plug outlet. (Illustration 2) 6. Push the power button in the “ON” position. (Illustration 3) 7. Push the restoration button (Illustration 4). This will start the heater. Note: When restarting the halogen bulb will start up slowly before getting to full power. Turning “OFF” 1. Push the power button to the “OFF” position. 2. Unplug the power cord from the wall outlet. Cleaning and Care Operating Instructions Illustration 1 Power switch in the “ON” position Clean...