. . . . . . . . Safety information Danger of electrocution! • Connect the appliance only to a 50 Hz grounded power socket with mains voltage of 230 V~ and that has been installed according to instructions. • Do not bend or squeeze the power cord. •To disconnect, always pull out the plug at the power socket, do not pull on the power cord. • Never touch the chimney, power cord and power plug with wet hands. • Do not use extension cables. • Do not wind the power cord around the casing of the chimn

Figure 12 GAS CONVERSION INSTRUCTIONS Warning: Conversion must be done by a qualified service technician. Conversion Instructions from Propane (LP) gas to Natural gas. 1. If installed, turn off gas supply to outdoor gas fireplace. 2. If installed, remove Propane (LP) gas hose from gas valve. 3. Remove electrode wire piezo ignitor. 4. Remove thermocouple from gas valve. 5. Remove two (2) bolts and two (2) nuts from valve bracket at bottom of outdoor gas fireplace. 6. Carefully remove valve bracke

*Available from the American National Standards Institute, Inc., 11 West 42nd St., New York, NY 10036. Page 4 CHG/CHR Figure 2 CLEARANCES Minimum Clearances From Combustible Construction (Figures 2 and 3) Side 6" Rear 6" Top 47" from top of unit or 96" from floor Floor Combustible Minimum Clearances From Combustible Construction with 20 lb. Propane (LP) Tank Attached to Outdoor Gas Fireplace (Figure 4) Side 6" Side, Corner Installation 7" Top 47" from top of unit or 96" from floor Floor Combusti

The National Fuel Gas Code, ANSI Z223.1 defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8m3 per kw) of the aggregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed, t

• Do not use the phone in your building. • Immediately call your gas supplier from a neighbor's phone. • Follow the gas supplier's instructions. • If you cannot reach your gas supplier, call the fire department. INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL CAST IRON VENTED FIREPLACE HEATER MODEL CIBV-30-2 EFFECTIVE DATE APRIL, 2000 WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Installat

Push up and outward to remove top louver. 2. Lower door assembly. 3. Release two door latches at bottom of firebox. 4. Grasp bottom of glass frame, lift glass frame upward in order to release glass frame from lip on top of firebox. 5. Align and place top of glass frame over lip on top of firebox. 6. Grasp bottom of glass frame, push inward and place glass frame onto firebox. 7. Attach two door latches onto bottom of glass frame. 8. Align and insert (4) mounting tabs on top louver with (4) slots

Any odors remaining after this initial break-in will be slight and will disappear with continued use. Standing Pilot Operating Instructions The standing pilot (750 millivolt system) is a continuous burning pilot. The pilot remains ON even when the main burner is OFF. 750 Millivolt System (Figures 40 and 41) When you ignite the pilot, the thermocouple produces millivolts (electrical current) which energizes the magnet in the gas valve. After 30 seconds to 1 minute time period you can release the

• If the control knob does not pop up when released, STOP and IMMEDIATELY call a qualified service technician or gas supplier. • If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and call your service technician or gas supplier. 10. Turn gas control knob counterclockwise to the "ON." 11. Close louver front assembly. 12. Turn on all electric power to the appliance (if applicable). 13. Set REMOTE/OFF/ON switch to REMOTE or ON. TO TURN OFF GAS TO FIREPLACE 1. Se

The pilot valve will be energized during the entire trial for ignition. This is normal operation for this gas ignition system. R-5627 Page 29 IP SYSTEM TROUBLESHOOTING SEQUENCE START • Turn OFF Gas Supply • Disconnect System Control Harness • Set witch ON Check for Proper Voltage at Control Harness (See Inset A -Voltage Should be 24V Between Thermostat and 24V Common, and 24V Between 24V Common and 24V Hot.) YES Plug Harness into SmartValve Control Wait for Internal Check Delay (SV9501) INSET A

• Do not use the phone in your building. • Immediately call your gas supplier from a neighbor's phone. • Follow the gas supplier's instructions. • If you cannot reach your gas supplier, call the fire department. POUR VOTRE SECURITE: Que faire si vous sentez une odeur de gaz: • Ne pas tenter d'allumer d'appareil. • Ne touchez a aucun interrupteur. Ne pas vous servir des telephones se trouvant dans le batiment ou vous vous trouvez. • Evacuez la piece, le batiment ou la zone. • Appelez immediatemen