Assessments - 4, GPA: 4.3 ( )

Fabricante : Panasonic Arquivo Tamanho: 305.46 kb Arquivo Nome : WJHDE500.pdf Língua de Ensino:

Lights in orange when a thermal error is detected inside the unit. (D HDD Access Lamps [HDD 1] [HDD 2] [HDD 3] [HDD 4] Lights while the HDD is accessed. Do not turn off the POWER switch while any of the access lamps is lit. (D Front Lids Four HDD openings are prepared inside the extension unit. Remove the lid to install the HDD. Replace the lid after installation. ® SCSI In connector [EXT IN] Connect the WJ-HD500 or other Extension Unit with a SCSI cable. © SCSI Out connector [EXT OUT] Connect another Extension Unit with a SCSI cable. © SCSI ID Switch [SCSI ID -/+] Press the upper or tower selector with a small headed screw driver to select the desired SCSI ID in the chain. (7) Termination Switch [TERMINATE ON/OFF] Set this switch to ON when the extension unit is located at the end of SCSI chain. Set this to OFF unless the unit is located at the chain end. © Terminal Board [THERMAL ERROR OUT] [G] A thermal error signal is supplied and OPERATE LED lights in orange when the inside temperature exceeds or falls below the limit. Connect these terminals with the WJ-HD500, [NC]: No connection ® Cooling Fan © AC Inlet [AC IN] Connect the supplied power cord. (0) Power Switch [POWER] Turn on this switch (peripherals) first, then the power of the WJ-HD500. Confirm all HDD access lamps go out before turning off this switch. Switch off the power of the WJ-HD500 first, then turn off this switch (peripherals): Signal GND Terminal [SIGNAL GND] Connect this terminal with other equipment’s SIGNAL GND to avoid possible grounding loop and noise if required. -3- Mounting HDDs A maximum of 4 HDD units (locally procured) can be mounted on one extension unit. This page describes how to install #1 HDD. Repeat the same procedures as #1 for #2 through #4 HDD. The HDD units should be installed into the proper openings in order as shown. Never skip or reverse the position order of the HDD units. 1 Remove the front lid. 1-1 Loosen the front lid fixing screw. 1-2 Slide the lid to the right and remove it. 2 Remove the HDD bracket #1. 2-1 Loosen 2 screws as shown. 2-2 Pull the bracket #1 out of the opening. 3 Disassemble the bracket #1. Separate it into the fixing bracket and dummy bracket by loosening 4 screws. Keep the removed fixing bracket and 4 screws so that they are to be used later. 4 Prepare an HDD unit. HDD Positions Inside The Lid HDD#4 HDD #3 HDD#2 HDD #1 ____:tnn TTT Dummy 5 Mount the HDD on the fixing bracket then fasten them together with 4 screws. -4- r 6 Set the unit address with jumper connector on the HDD as shown. Note: For further details, refer to the instructions included in the HDD unit. HDD #2 & #4 (SLAVE) Jumper Position HDD #1 & #3 (MASTER) Jumper Position 8 Plug the 2 connector harness to the installed HDD as shown. Jumper Connector 9 Repeat above steps for HDD #2 through #4. -5- i ■ Connection & Switch Setting SCSI Connection The Digital Disk Recorder WJ-HD500 controls the extension units through the SCSI chain. 1 Connect between the EXT STORAGE port on the WJ-HD500 and the EXT IN port on the 1st extension unit with the supplied SCSI cable. 2 Connect between the EXT OUT port on the 1st extension unit and the EXT IN port on the 2nd extension unit with the supplied SCSI cable. Repeat connections in the same manner for the following extension units. 3 The 3rd extension unit must be a WJ-HDE505 if further extension unit is connected. Use a WJ-HDE500 if the 3rd unit is located at the end of SCSI chain. Extension is available up to 6 units. 1 Digital Disk Recorder WJ-HD500 SCSI ID = 6 & 7 HIS; Extesion Unit #1 WJ-HDE500 SCSI ID = 5 О irr ф £> « О 55 о S Extesion Unit #2 WJ-HDE500 SCSI ID = 4 -J—--0—I Extesion Unit #3 WJ-HDE500 or WJ-HDE 505* SCSI ID = 3 ..............^ Wtô §= \ *y » Extesion Unit #4 WJ-HDE500 SCSI ID = 2 Г 2 L q IP........i.............-......H Hi«*»

Baixe o seu

Para fazer o download, introduza 2 dígitos :