Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
For maximum performance, the spark arrester screen should be periodically cleaned as follows. See Figure 16. 1. Remove engine cover to expose muffler. Remove the spark arrester from the muffler. The arrester is press-fit in place; there are three screws to remove. 2. Use a plastic scraper or wire brush to remove carbon deposits from the arrester screen and wipe clean exhaust base. 3. Inspect the screen carefully, and replace any screen that has been perforated, distorted, or is otherwise unserviceable. 4. Press the spark arrester into the exhaust base. If carbon accumulation in the muffler or cylinder are severe, or if you do not notice an improvement in performance after servicing, have the unit inspected by an authorized servicing Shindaiwa dealer. Arrester Screen Cover Arrester Screen Muffler Figure 16 Long Term Storage Whenever the unit will not be used for 30 days or longer, use the following procedures to prepare it for storage: n Clean external parts thoroughly. n Drain all the fuel from the fuel tank. IMPORTANT! All stored fuels should be stabilized with a fuel stabilizer such as STA-BIL™ if Shindaiwa One oil with fuel stabilizer is not used. To remove the remaining fuel from the fuel lines and carburetor and with the fuel drained from the fuel tank. 1. Prime the primer bulb until no more fuel is passing through. 2. Start and run the engine until it stops running. 3. Repeat steps 1 and 2 until the engine will no longer start. n Remove the spark plug and pour about 10 cm3 (1/4 oz.) of 2-cycle mixing oil into the cylinder through the spark plug hole. Slowly pull the recoil starter 2 or 3 times so oil will evenly coat the interior of the engine. Reinstall the spark plug. n Before storing the unit, repair or replace any worn or damaged parts. n Remove the air cleaner element from the unit and clean it as outlined on page 10. n Store the unit in a clean, dust-free area. CAUTION! Gasoline stored in the carburetor for extended periods can cause hard starting, and could also lead to increased service and maintenance costs. Troubleshooting Guide ENGINE DOES NOT START What To Check Remedy Possible Cause Consult with an authorized servicing dealer. Tighten and re-test. Consult with an authorized servicing dealer. Refill with clean, fresh unleaded gasoline with a pump octane of 87 or higher, mixed with a 2-cycle air cooled mixing oil that meets or exceeds ISO-L- EGD and/or JASO FC classified oils at 50:1 gasoline/oil ratio. Replace fuel filter or vent as required. Re-start. Consult with an authorized servicing dealer. Move switch to “I” (ON) position and re-start. Consult with an authorized servicing dealer. Crank the engine with the plug removed, re-install the plug and re-start. Clean and re-gap the plug to 0.6 mm (0.024 in.). Re-start. Replace the plug with a NGK CMR5H or equivalent resistor type spark plug of the correct heat range. Set spark plug electrode gap to 0.6mm (0.024 in.). Faulty recoil starter. Fluid in the crankcase. Internal damage. Loose spark plug. Excess wear on cylinder, piston, rings. Fuel incorrect, stale, or contaminated; mixture incorrect. Check for clogged fuel filter and/or vent. Priming pump not functioning properly. The ignition switch is in “O” (OFF) position. Shorted ignition ground. Faulty ignition unit. If the plug is wet, excess fuel may be in the cylinder. The plug is fouled or improperly gapped. The plug is damaged internally or of the wrong size. NO Does the engine crank? YES NO Good compression? YES NO Does the tank contain fresh fuel of the proper grade? YES NO Is fuel visible and moving in the return line when priming? YES NO Is there spark at the spark plug wire terminal? YES Check the spark plug. Troubleshooting Guide (continued) LOW POWER OUTPUT What To Check Possible Cause Remedy Operator is overworking the unit. Carburetor mixture is too lean. Improper fuel ratio. Fallen leaves or debris on intake cover. Fan, fan cover, cylinder fins dirty or damaged. Carbon deposits on the piston or in the muffler. Clogged air cleaner element. Loose or damaged spark plug. Air leakage or clogged fuel line. Water in the fuel. Piston seizure. Faulty carburetor and/or diaphragm. Overheating condition. Improper fuel. Carbon deposits in the combustion chamber. Use a lower throttle setting. Consult with an authorized servicing dealer. Refill with clean, fresh unleaded gasoline with a pump octane of 87 or higher, mixed with a premium 2-cycle air cooled mixing oil or equivalent at a 50:1 gasoline ratio. Clean the intake cover. Clean, repair or replace as necessary. Consult with an authorized servicing dealer. Service the air cleaner element. Tighten or replace the spark plug. See page 11. Repair or replace fuel filter and/or fuel line. Replace the fuel. See page 7. Consult with an authorized servicing dealer. See above. Check fuel octane rating; check for presence of alcohol in the fuel. See page 7. Refuel as necessary. Consult with an authorized servicing dealer. Is the engine overheating? ...
Este manual também é adequado para os modelos :Sistemas de ventilação - 68907-94311 (3.9 mb)
Sistemas de ventilação - EB2510/EVC (3.9 mb)
Sistemas de ventilação - EB3410 (3.9 mb)
Sistemas de ventilação - EB3410/EVC (3.9 mb)