Assessments - 3, GPA: 3
(
)
)
|
Facilidade de uso
above electric burners or 75 cm. above gas or mixed-fuel burners. (Fig. 3). Electrical connection Fig. 3 The hood has a power cord with moulded plug with earth connection to be connected to a wall outlet of 230 V. The power outlet should be pre-mounted in such a way that the power cord is invisible when the hood is fully mounted. The power cord length is 1,25 m. Min 65 cm Min 75 cm As it is then hard to disconnect the power plug for cleaning and service, an easy accessible two pole switch should be fitted. The switch should conform to regulations with an opening distance between contacts of not less than 3 mm. 43 Mounting of hood . Fit the drilling scheme onto the wall at the right height. (Fig. 4) The lower edge of the scheme correspond to the lower edge of the cooker hood. . On the drilling scheme is printed a line corresponding to the centre of the appliance; with a pencil draw a line up to the ceiling, this will aid installation procedures. (Fig. 4) . Drill as indicated on the scheme and fit two dowels, two hooks and two screws 5x45. (Fig. 4) Fig. 4 . Hang the hood, adjust the position using the screws on the hooks of the hood. (Fig. 5) . Release the grease filters. (Fig. 1) . From the inside of the hood mark on the wall the point corresponding to the hole which will be used to fix definitively the hood. (Fig. 6) . Remove the hood. . Drill two hole (O 8mm) and fit two dowels. (Fig. 6) . Hang the hood again on the hooks. . From inside of the hood insert the definitive fixing screws. (Fig. 6) Fig. 5 Fig. 6 44 . Dismount the chimney support from the chimney unscrewing the two side screws (one per side of the chimney- conserve them). (Fig. 7) . Dismount the deflector "b" from the chimney support unscrewing the two screws that fix the deflector to the chimney support (conserve the screws). (Fig. 7) . Fit the chimney support onto the wall close to the ceiling. The support has a reference mark, this must match the line previously drawn on the wall. (Fig. 7) . Mark with a pencil the hole to be done and drill the holes (O 8mm). . Insert two wall dowels and fix the telescopic chimney support with two screws 5x45. (Fig. 7) The power plug must be disconnected from the mains during the mounting procedure. Make the choice of how to use the hood: Exhausting version . Fit a O 150 mm exhausting pipe or flex tube on the hood outlet on top of the motor housing and connect it to the wall or roof outlet pipe. Recirculating version . If not already fitted, fit the connection ring (a Fig. 7) supplied (bajonett attachment - turn clockwise and fix with a screw) on the deflector b. . Insert the deflector in the chimney support and fix it with two screws (Fig. 7). . Fit a O 150 mm exhausting pipe on the motor outlet connection ring sufficiently long to reach the connection ring on the deflector. For both versions: . Now connect the power plug to the wall outlet. . If a no return valve is used check that it can open correctly and is not blocked by the flex tube . Fix the chimney top part on its support with two screws (Fig. 7). . Slide the lower section of the chimney downwards and insert it on its proper housing on the upper side of the hood (Fig. 7). Mounting of carbon filter (for recirculating version) . Remove the grease filter. . Fix the carbon filter with its two screws (Fig. 8). . Replace the grease filter. b a Fig. 7 Fig. 8 45 Using the hood The hood has one variable speed motor. For the best performance, we recommend using the low speeds in normal conditions and the high speeds in particular cases of strong odour and vapour concentration. We recommend starting up the hood a few minutes before cooking and keeping it running until all the odours have been eliminated. Important to know If the hood is run at the same time as a burner or fireplace that depend on ambient air (for example gas, Diesel, coal or wood heaters, water heaters, etc.) be careful, because the hood, when it exhausts the air, removes the ambient air required by the burner or fireplace for combustion. Not valid if the cooker hood is used in recirculation mode. 0 123 5 MIN 0 I FC A BEFCDG H I A – Motor OFF button B – ON button and motor speed selection button 1 - 2 - 3 - 1 - 2 - . . . . E – Speed 1 LED F – Speed 2 LED and grease filter saturation LED (flashes) C – Speed 3 LED and carbon filter saturation LED (flashes) D – Intensive speed indicator LED G – Intensive speed ON switch H – OFF lamp button I – ON lamp button If the hood fails to operate correctly, briefly disconnect it from the mains power supply for almost 5 sec. by pulling out the plug. Then plug it in again and try once more before contacting the Technical Assistance Service. Intensive speed button This speed should be used when the concentration of cooking fumes or odours is particularly strong (for example when frying, cooking fish etc.). The fast speed will run for about 5 minutes and then return to the speed previously set automatically (1, 2 or 3), or switch off if no speed was selected. T...
Este manual também é adequado para os modelos :Fans - DEFI UK EFC 939 X (102.92 kb)