Assessments - 0, GPA: 5
(
)
)
|
Facilidade de uso
Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property damage. Reading this book will also help you to get all of the benefits from your water filter. • Your water filter will improve your water as described on page 11. It will not soften water or remove iron. It will not purify polluted water or make it safe to drink. Also see the specifications on page 18. • Protect the filter and piping from freezing. Damage from freezing voids the filter warranty. See page 13. PLEASE READ AND COMPLY WITH THE FOLLOWING GUIDES TO PREVENT DAMAGE TO THE FILTER OR OTHER PROPERTY, PERSONAL INJURY, OR POSSIBLE FATAL SHOCK. • THIS FILTER WORKS ON 24 VOLTS ONLY. BE SURE TO USE THE TRANSFORMER INCLUDED, AND PLUG IT INTO A 120V OUTLET. • Unplug the transformer right away if the power cable should become damaged or frayed. Make repairs before plugging back into the power outlet. • Always unplug the filter from electrical power before removing outer valve covers. 4 SECTION 1 WATER FILTER START-UP II lB. CHECK LIST OF ALL STEP BY STEP GUIDES TO INSTALL Refer to the Installation for step-by-step guides. Manual, part no. 7146611, To be sure you have done all the filter, read the following list. Page to are in the Installation Manual. steps to install the numbers referred Is the house water flow going INTO INLET? Trace piping to be sure.., the filter valve page 9. Is the plumbing bypass valve (or 3 valves) set for SERVICE?... See FIG. 8, page 18 ofthis manual. VALVE INLET Is the valve drain hose connected the right and without sharp bends or kinks that could or reduce water flow?., page 14. way, stop v' Is the filter transformer.., into an inside, page 17. power cable connected to the and is the transformer plugged 120V-60Hz electrical outlet?... Be sure to restart the water heater.., page 18. SECTION 1 WATER FILTER START-UP I 1 10. SANITIZING THE WATER FILTER Care is taken at the factory to keep your water filter clean and sanitary. Materials used to make the filter will not infect or contaminate your water supply, and will not cause bacteria to form or grow. However, during shipping, storage, installing and operating, bacteria could get into the filter. For this reason, sanitizing as follows is suggestedG when installing. on the face plate until RCHG begins to flash in the display su Press and HOLD button [] _cMHG12:00 (12:00 AM began to flash when the transformer was plugged in). Water will begin to run from the drain hose as the filter valve moves into backwash position. After 5 to 10 minutes, press [] again to move the filter valve into fast rinse position (water stops, then begins to run from drain hose again). m In about 2 minutes, PUT THE BYPASS VALVE(S) IN BYPASS POSITION (SEE FIG. 8, PAGE 18). Then, press button [] once again to return the filter valve to service position. Doing this releases water pressure in the filter. 3. Carefully remove the large plastic clip at the filter valve inlet (see Key No. 41, page 26). Pull the valve adaptor from the filter inlet. NOTE: If bypass valve, Sears Stock No. 42-3437 is installed, or if plumbing is too rigid to move, also disconnect the outlet side and move the filter away from plumbing. 4. Put 1 teaspoon (0.1 ounce) of calcium hypo- chlorite into the valve inlet as far as possible. NOTE: You can buy calcium hypochlorite in tablet or granular form using trade names such as Perchloron and HTH. m Be sure the valve inlet is clean, for a good sealing surface for the valve adaptor o-ring. Then, reconnect plumbing to the filter. AFTER INSTALLING THE LARGE PLASTIC CLIP, PULL OUTWARD ON THE VALVE ADAPTOR TO BE SURE IT'S ...
Este manual também é adequado para os modelos :Purificadores de água - Kenmore 625.348241 (1.17 mb)
Purificadores de água - Kenmore 625.348251 (1.17 mb)
Purificadores de água - Kenmore 625.348241 (1.17 mb)
Purificadores de água - Kenmore 625.348234 (1.17 mb)