ENTRETIEN Mantenimiento Apres avoir peche avec votre moulinet XS, vaporisez genereusement le produit nettoyant Reel Kleen sur la partie exterieure du moulinet, puis essuyez a l’aide d’un linge sec pour enlever la salete, les debris et l’humidite. Lubrifiez les roulements a l’aide du lubrifiant pour roulement Reel Butter et huilez l’arbre de tambour avec l’huile Reel Butter au moins une fois pendant la saison de peche, ou plus au besoin, selon la methode decrite ci-dessous: UTILISATION NORMALE Us

PRODUCT SCHEMATIC Machined Magnesium Alloy Frame and Covers Provides superior casting control and flexibility ABEC grade stainless steel ball bearings & Infinite antireverse roller clutch bearing Maximum Casting Distance and Control ™ Rule the water.TM Model Bearings Gear Ratio Line Capacity (lbs. - yds.) XS1000 10+1 6.3:1 8-180 10-150 12-120 XS600 6+1 6.3:1 8-180 10-150 12-120 XS600 6+1 5.0:1 8-225 10-200 12-175 XS1000 10+1 5.0:1 8-225 10-200 12-175 OWNER’S MANUAL Slide Button Up to Open Brake

12-Lb. Weight at 2, 4, and 6 MPH 2 MPH 4 MPH 6 MPH Act u al De pt h of Weigh t ( ft.) Amount of Cable in Water (ft.) 4 MPH 6 MPH Amount of Cable in Water (ft.) A c tualDepth of W e ight ( ft.) 2 MPH 8-Lb. Weight at 2, 4, and 6 MPH 2 MPH 4 MPH 6 MPH Act u al De pt h of Weigh t ( ft.) Amount of Cable in Water (ft.) Blowback Charts 10-Lb. Weight at 2, 4, and 6 MPH 13 Adjusting the Depth Meter The Cannon Depth Meter provides non-slip accuracy, plus easy resetting. To reset, just slide the meter away

In Canada, parts may be ordered from any of the Canadian Authorized Service Centershown on thenclosed list. Be sure to provide the MODEL and SERIAL numbers of your downriger when ordering parts. Please use the corect part numbers from the parts list. Payment for any parts ordered from the CANON parts department, may be by cash, personal check, Discover Card, MasterCard or VISA. Torder, cal 1-80-27-643 or FAX 1-80-527-464. > PART OF ASSEMBLY > ITEM CANOT BE SOLD SEPARATELY * PARTS USED BUT NOT SH

Examine the top of the terminator and note the Unwind about 2 feet of cable order shown in the detail to run cable. and thread the cable through the rubber cushion. Lead cable into HOLE A. Pull six inches of cable through. Thread cable through swivel, then up into bottom of the terminator. Lead cable out of HOLE B and into HOLE C. Push the cable until its end touches the inside of the terminator hook. HOLE A Swivel TIP: Use only straight cable, not kinked. Tighten cable by squeezing terminator u

and then wipe clean to remove old grease, debris, and moisture. • Grease the main drive gear, pinion, and worm shaft with Reel Butter® Grease at least once per fishing season, or more often if needed, as shown below: COMFORT NECK GRIP Ergonomically styled for improved comfort DUAL BEARING PINION SUPPORT Pinion is supported on both ends by bearings to prevent damage or wear to the gear set or axle ABEC BALL BEARINGS 7 Stainless Steel Ball Bearings and one infinite anti-reverse clutch bearing

Spool to ^Lube Spool Axle OWNER’S MANUAL iJ Z2SŒX1D SPINNING REEL X\ /ZOeA/7" RmIi tU m/aXm: MADE IN THE USA Model U SSŒJU MODEL OPTIONS Bearings Gear Ratio Line Capacity Clbs. - yds.] S2500 6-200 B-1BD 10-120 3 Year Warranty Ardent is able to provide the longest warranty in the industry because every Ardent reel is hand-crafted and performance tested prior to shipment. From the braking system to the spool shaft, we guarantee quality and craftsmanship. A smooth, high-performance fi