VO \'u *40 * BO KÂ O AO 50 BO 70 BO * 1 ‘ * ‘ * jr 3 2.75" (70)' ~D Front View 1.5" (38)' 4.75" (121) Side View Specifications — Table A Model RaTeg7(;F) Contacts Range (°F) Max AC Volts Max AC Amps WTL-121 40-80 SPST 30 V 1 Amp GENERAL Note: Type WTL thermostats are designed for temperature control service only. Because they do not fail safe, they should not be used for temperature limiting duty. WARNING: Users should install adequate back-up controls and safety dev

All can be used, but the 75/25 mixture is recommended for general welding. For aluminum welding, use 100% Argon. Either type gas may be obtained at your local welding supply outlet. Secure cylinder in place on your welding machine or other support to prevent the cylinder from falling over. REGULATOR This regulator is designed to be used with straight Argon or Argon mix gas. A threaded adapter is needed if CO2 is used. An adapter is available at your local welding gas supplier to change between t

• Install and secure cylinders in an upright position by chaining them to stationary support or equipment cylinder rack to prevent falling or tipping. • Never allow a welding electrode to touch any cylinder. • Turn face away from valve outlet when opening cylinder valve. • Keep protective cap in place over valve except when cylinder is in use or connected for use. • Read and follow instructions on compressed gas cylinders, associated equipment, and CGA publication P-1. ! DANGER Never use flammab

Do not mount adjacent to space around wires in the conduit with rock wool. a large magnetic contactor, as vibration and shock will cause thermostat to interact erratically – resulting in chattering of the contactor. WARNING: Do not twist or uncoil the coiled element on top of the case. The proper location of a heavy duty room thermostat is important to assure good performance. 1. Locate where air circulates freely. 2. Never install on or near outside wall. 3. Keep away from windows or doors. 4.

Overview The Cypress Envirosystems Wireless Pneumatic Thermostat (WPT) retrofits an existing pneumatic thermostat to provide Direct Digital Control (DDC) like zone control functionality at a fraction of the time and cost without disturbing occupants. The WPT enables remote monitoring of zone temperature, branch pressure, remote control of setpoints, and programmable setback or setup of the pneumatic HVAC systems. It also enables integration with utility Demand Response programs. The WPT USB Hub

Trademarks Control4 is a registered trademark of Control4 Corporation. Other product and company names mentioned in this document may be the trademarks or registered trademarks of their respective owners. Copyright Copyright © 2005-2006 Control4 Corporation. All rights reserved. No part of this publication may be reproduced, photocopied, stored on a retrieval system, or transmitted without the express written consent of the publisher. Control4 Corporation 11734 S. Election Road, Suite 200 Salt L

You may hit the START button if you are ready with a full hopper of fuel. * The thermostat is available separately from the stove. The 3 modes are as follows: When the red FEED RATE lights 3 and 4 flash, that is the High/Low Thermostat Cycle (optional *). 1When the red FEED RATE lights 1 and 2 flash, that is the On/Off Thermostat Cycle (optional *). 2When the red FEED RATE lights 1 and 4 flash, that is the manual function. 3IMPORTANT: PLEASE READ BEFORE STARTING YOUR STOVE The controller on your

Follow all lock out/tag out procedures established by the user. Verify all power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to the equipment. 1. Open kit and remove new parts. 2. Insert the new metal thermostat well into the small, non flared end of the tube and seal it with V to V2 inch of food grade silicone. Let set for 15-30 minutes. 3. Turn the machine off. 4. Remove panels, as needed. 5. Gently pull gray sensing bu

19 Two-stage furnace and two-stage AC configuration IMPORTANT! The B terminal is for reversing valve-heat. DO NOT connect the B terminal to the common side of the transformer. ViewStat Communicating Thermostat 27J ViewStat Installation and Wiring NOTE Roof top unit (two-stage heat and two-stage cool) configuration. ROOF TOP UNIT 120 ;i VAC ie: гЩ i I VAC ....... FAN RELAY Black (common) (from MiniVerter) 24V FIELD WIRING FACTORY WIRING OPTIONAL 24V FIELD WIRING (SEE NOTE)

This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not liable for any claim made by a third party or by an AMX Dealer for a third party. This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitati