Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
Hardware to attach the thermometer are two wing nuts. Finger tighten the wing nuts on the inside of the lid. DO NOT OVERTIGHTEN the wing nuts (Fig. 24 and 25). Fig. 24 Fig. 25 Assemble the Warming Rack and the Grease Tray Assemble the Propane Tank Retainer 1. Insert the ends of the Propane Tank Retainer into the holes provided in the right side panel (Fig. 29). Use the pins provided with the Retainer to secure the Retainer in place. Fig. 29 Assemble the Wire Shelf 1. Insert the ends of the Wire Shelf into the holes provided in the back panel. Use a screwdriver to attach the shelf to the base with two screws (Fig. 30). Fig. 30 Grill Assembly(continued) Assemble the Doors and the Tool Hook NOTE: On some models, the Doors and the Tool Hook are pre- assembled at the factory. 1. Install both doors by first 2. Assemble the Tool Hook to inserting the lower pin and the the left door using three upper pin in the hinge holes at screws. Tighten the screws the same time (Fig. 31). with a screwdriver (Fig. 32). 10 Fig. 31 Fig. 32 1. Assemble two sets of handles with parts illustrated in (Fig. 33). Fig. 34 Assemble the Doors Handles Fig. 35 First Last Fig. 36 4. Tighten both screws with a screwdriver. Access holes are provided on the inside of each door (Fig. 36). Shoulder Narrow part of Slot Fig. 33 Lockwasher Long screw with shoulder Short screw Lockwasher touches Screw Head 2. Loosely engage the screws only several turns (Fig. 34). In the next step, the screw heads will engage slots in the doors from the outside before they are tightened. 3. Insert the screw heads into the slots in the outside of the door. The screws must be inserted in sequence. First, slide the short screw into the slot. The lockwasher must touch the screw head. Next, insert the long screw (Fig. 35). PLEASE NOTE: Only the slender portion of the long screw will slide past the narrow part of the slot. This feature locks the shoulder screw in place. Grill Assembly(continued) Assemble the Side Tables 1. Align the tabs on the Side 2. Use firm pressure to push the Tables with the slots on the Side Tables down and into side of the grill (Fig. 37). place (Fig. 38). The joint between the Side Tables and the Grill will be even. Fig. 37 Fig. 38 3. Engage the locks by firmly pushing the tabs into the slots (Fig. 39). Be sure to engage two locks on each side table. Fig. 39 20# LP Cylinder Installation NOTE: Your 9998 Series grill is set up from the factory to use a 20# refillable LP cylinder. You may purchase a 20# LP cylinder from the store where you bought your grill, or from your local propane dealer. WARNING This procedure MUST be performed OUTDOORS only! Be sure the L.P. cylinder valve is closed. Attach to the grill. Read and follow the directions on the cylinder. 20# LP Cylinder Installation(continued) 1. Set the LP Cylinder in the Cylinder Support location with the outlet valve facing toward the door opening of the grill. Lower the Tank Support to engage the Cylinder Collar (Fig. 40). Fig. 40 CAUTION In the connection process, the grill side of the connection will seal on the back-check in the valve, resulting in a slight resistance. The connection requires about one-half to three- quarters additional turn to complete the connection. To disconnect, turn counterclockwise. Tighten by hand only. DO NOT use tools. IMPORTANT! TO ENSURE PROPER GAS FLOW, BURNER CONTROL VALVES MUST BE “OFF” BEFORE OPENING THE GAS CYLINDER VALVE. WARNING: During assembly of the grill and when attaching or replacing the L.P. gas cylinder, insure that the gas supply hose is free of kinks and/or damage and is at least 3 inches away from hot surfaces such as the grill casting. 3. Check that the cylinder valve is closed by turning the cylinder knob clockwise to a full stop (Fig. 41). Fig. 41 11 20# LP Cylinder Installation(continued) 4. Check that all grill burner knobs are in the off position (Fig. 42). Fig. 42 5. Remove the protective caps from the cylinder valve and coupling nut. NOTE: The coupling nut connects to the large outside threads on the valve outlet. 6. Hold the hose in one hand and insert the nipple into the valve outlet. Be sure the nipple is centered in the valve outlet. Hand-tighten the coupling nut, taking care not to cross-thread the connection (Fig. 43). Fig. 43 No Smoking TYPE 1 7. Turn the coupling nut clockwise, tighten to a full stop. If you cannot complete the final connection, disconnect the coupling nut and repeat steps 6 and 7. If you are still unable to complete the connection, DO NOT use this hose and valve! 8. Check that the hose has no kinks or sharp bends and clears areas that will become hot during use. Never put strain on the hose where it joins a fitting. 9. BEFORE lighting grill, check all connections for leaks using the procedure as shown in the section titled “LEAK TESTING”. Leak Testing - Refillable Cylinders DANGER TO PREVENT FIRE OR EXPLOSION HAZARD: • NO SMOKING. DO NOT use or permit sources of ignition in the area while doing a leak test. • P...