Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Do not bend the hooks while inserting or removing the Fryer Grease Pan. Fryer Grease Pan Hooks 19Electrode Wire Fryer Panel Step15 • ....Assemble Front Fryer Heat Shield. 15-A Fryer Heat Shield Engage Tabs into Rectangle Holes Electrode Wire 15-A. Assemble Fryer Heat Shield. • ....NOTE: Place the Fryer Heat Shield between the Fryer Panel and the Flexible Fuel Hose. Do not pinch Electrode Wire. • ....Engage the two tabs on the Heat Shield downward into the rectangle holes. 15-B Fryer Heat Shield 15-B. View showing the Fryer Heat Shield properly installed. 20 ....Route the Electrical Wires under the Right Side Table. ....Note the location of the Electrode Module.Step1616-A 16-B Electrical WireWire Support Electrode Module Back Burner Electrical Wire 16-A 16-B Electrical WireWire Support Electrode Module Back Burner Electrical Wire 16-A. Route the Back Burner Electrical Wire through the Wire Support. 16-C 16-D Wire Tie Electrical Wire 16-C. Route the Main Burner Electrical Wires through the Wire Tie. • ....Wrap the Wire Tie around the wire and secure in place. 21 ....Assemble the electrode Wires and the Battery to the Electrode Module. Step1717-A Electrode Module Igniter Button Wires (Note: Large Tabs) 9-Volt Battery TEST THE IGNITER: A SPARK SHOULD APPEAR AT ELECTRODE TIP. IF THE SPARK DOES NOT APPEAR: -CHECK THE WIRE CONNECTIONS TO THE MODULE. -CHECK PROPER ASSEMBLY OF FRESH 9-VOLT BATTERY. Back Burner Electrode Wire 17-A. Firmly push the Electrode Wires into the Electrode Module. ....Assemble the 9-Volt Battery to the Electrode Module. ....NOTE: The polarity is marked on the Electrode Module. 2217-A Electrode Module Igniter Button Wires (Note: Large Tabs) 9-Volt Battery TEST THE IGNITER: A SPARK SHOULD APPEAR AT ELECTRODE TIP. IF THE SPARK DOES NOT APPEAR: -CHECK THE WIRE CONNECTIONS TO THE MODULE. -CHECK PROPER ASSEMBLY OF FRESH 9-VOLT BATTERY. Back Burner Electrode Wire 17-A. Firmly push the Electrode Wires into the Electrode Module. ....Assemble the 9-Volt Battery to the Electrode Module. ....NOTE: The polarity is marked on the Electrode Module. 22 Fasten the Rear Trim Plate to the Grill Cart. 18-A FIREBOX VP (x2) REAR TRIM PLATE VP 18-B 18-C. View showing Rear Trim Plate properly installed. Rear Trim Plate to the Firebox with two Screws (VP). 18-C REAR TRIM PLATE ROUTE ELECTRICAL WIRE THROUGH NOTCH -DO NOT PINCH- 18-A. Fasten the • ....NOTE: Route Electrical Wire through notch. Do not pinch wire. • ....Tighten all fasteners. (VP) Self Tapping Screw (2) Qty. .... Hardware shown actual size Step18 23 Hardware shown actual size (XR) M5 x 15mm Flat Head Screw (8) Qty. ....Fasten both Left and Right Doors to the Grill Cart. ....Attach the Tool Hook to the Right Door. 19-C Step1919-B TOOL HOOK TOOL HOOK XR (x4) 19-C. Squeeze the Tool Hook to slip into the mounting brackets. RIGHT DOOR (with Tool Hook Brackets) LEFT DOOR (without Tool Hook Brackets) TOOL HOOK Brackets 19-C Step1919-B TOOL HOOK TOOL HOOK XR (x4) 19-C. Squeeze the Tool Hook to slip into the mounting brackets. RIGHT DOOR (with Tool Hook Brackets) LEFT DOOR (without Tool Hook Brackets) TOOL HOOK Brackets 19-B. Fasten the Right Door to the Grill Cart with four Flat Head Screws (XR). • ....NOTE: Right Door has Tool Hook Brackets. Left Door does not have Tool Hook Brackets. • ....Repeat Step 19-B to attach the Left Door. • ....Tighten all fasteners. 24 20-A .... Fasten the Door Handles to the Doors. .... Attach the Tool Hook to the Right Door. .... NOTE: M4 x 5mm Screws are factory installed into the Handles. Step 20 Hardware shown actual size (EZ) M4 X 5mm Screw (4) Qty. EZ (x2) DOOR HANDLE RIGHT DOOR 20-A. Fasten one Door Handle to the Right Door with two Screws (EZ). Repeat Step 20-A to assemble one Door Handle to the Left Door. .... Tighten all fasteners. .... Install four Heat Tents™. .... Install four Cooking Grates. .... Install two Warming Racks. Step 21 21-A Heat Tents™ Cooking Grates Warming Racks Burners 25 Step 22 21-B Heat Tents™ 21-B. Install four Heat Tents™ over the Burners. • ....The Heat Tents™ are located using the alignment pins. • ....Place Basket and Thermometer in the Fryer Assembly. 21-D. Place the Warming Racks in the back of the Firebox. ....Align posts into holes. 21-D Warming Racks 22-A Fryer Basket Thermometer 22-B 22-A. Place the Basket and Thermometer in the Fryer Assembly. ....Use the Tab on the Thermometer to keep it securely in place in the reservoir (See Fig 22-B). Tab 26 21-C. Install four Cooking Grates with smooth surface down. ....Locate the Power Grates in the center positions. 21-C Standard Grate Power Grates Standard Grate .... Assemble two Grease Cup Supports to the Grease Pan. Note: The Grease Pan is shown up-side-down during this step. 23-A (VP) Self Tapping Screw (4) Qty. Hardware shown actual size Grease VP (x4) Cup Support Note: Lip is up. 23-A. Attach the Grease Cup Support to the Grease Pan with two self-tapping screws (VP). Step 23 Note: Flange is down. Grease Pan .... Install the Grease Pan. .... In...