Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Perform a leak test each time the gas supply cylinder is connected to the regulator. Leak test anytime a part of the gas system is replaced. 2. Perform a leak test at least once each year whether the L.P. gas supply cylinder has been disconnected or not. 3. Have a dealer check the cylinder for deterioration after 12 years, according to DOT regulations. Immediately replace the cylinder if any deterioration is found. CAUTION Inspect the gas supply hoses before each use. Open the door to inspect the hose assembly below the grill. Also inspect the hose assembly below the side burner. If there are cuts, damage, excessive abrasion or wear, replace the hoses prior to operating the appliance. During assembly of the grill and when attaching or replacing the L. P. gas cylinder, insure that all gas supply hoses are free of kinks and/or damage and are at least 3 inches away from hot surfaces such as the grill housing. Use only hose replacements specified in the parts list. 16 Start-Up Check List WARNING Failure to follow these safety steps before using the grill each time could result in a fire that could be hazardous to you, your appliance or property. It is especially important to observe these steps after the grill has been stored, moved or cleaned. 1. Regularly check the burner venturi tubes for blockage from an insect nest. Read “Cleaning the Venturi” in the section titled “Care, Maintenance, and Cleaning”, and also the section titled “Troubleshooting”. 2. Check that all the burner venturi [H] are set over the valve outlets [J] correctly. The valve orifice [K] must be inside the venturi (Fig. 21). 3. Inspect the gas supply hoses before each use. Hoses can be burned or chafed if they are routed improperly. See that the hoses have no kinks, sharp bends or tension. Insure that the hoses are at least 3 inches away from any hot surface. 4. Use only the gas specified. 5. Keep the grill on a level surface. 6. Keep the grease pan empty at start up. J K H REPRESENTATIVE ILLUSTRATION Fig. 21 CAUTION DO NOT add charcoal or lighting fluid! 2 3 4 WARNING THE FOLLOWING RULES MUST ALWAYS BE FOLLOWED IN THIS ORDER (Fig. 22): 1. OPEN THE GRILL LID! Any attempt to light the grill with the lid down could cause an explosion. 2. Check that the burner control knobs are turned to “OFF”. 3. Turn on the fuel supply. For an L.P. gas cylinder, turn the top cylinder valve knob counterclockwise one rotation to open. 4. DO NOT stand with your head or arms over the grill. Lighting Instructions 1 Fig. 22 Fig. 23 REPRESENTATIVE ILLUSTRATION (2) Right Side Burner Knobs Rear Infrared Burner Knob (Rotisserie) (6) Control Knobs for Main Cooking Area (2) Igniter Switches 17 Lighting Main Burners 1. Push and turn one of the three left main burner control knobs counterclockwise to the “HIGH” position. Wait 5 seconds. (Fig. 23, 24, and 25) 2. Press and hold the left electronic igniter button. You will hear a snapping sound. (Fig. 25) 3. If the burner does not light in 4 seconds, turn the control knob to OFF and wait 5 minutes for the gas to clear before trying again. 4. Repeat steps 1 through 3 to light the remaining burners. NOTE: The right main burners are ignited by using the right side igniter (Fig. 26). 5. If the burner does not light on the second try, turn the control knob to OFF and wait 5 minutes for the gas to clear, and then try match-lighting the burner. Match Lighting - Main Burners 1. Strike and place the burning long wooden match (or butane lighter with extension) through the spaces in the grill grates near the ports of the back crossover burner between the heat tents. (Fig. 27). 2. Push and turn the control knob counterclockwise to the “HIGH” position. 3. Repeat steps 1 and 2 to light the remaining burners. CAUTION Use a LONG wooden match or a butane lighter with an extension. Make sure all burner controls are off except for the burner being lighted. If a long-reach match or lighter is not accessible, there is a match extension provided, attached to the inside of the door. Insert a match in the holder end of the extension, strike and place the burning match near the BURNER being operated. Fig. 25 Fig. 24 Fig. 27 Fig. 28 Fig. 29 Fig. 26 Lighting Side Burner CAUTION The side burner cover MUST BE OPEN during lighting and while using the side burner (Fig. 28). NEVER operate the side burner with the side burner cover in the closed position. 1. Push and turn the side burner control knob counterclockwise to the “HIGH” position. (Fig. 28) 2. Immediately press and hold the electronic igniter button (Fig. 28). You will hear a snapping sound. 3. If the burner does not light in 4 seconds, turn the control knob to OFF and wait 5 minutes for the gas to clear before trying again. 4. If the burner does not light on the second try, turn the control knob to OFF and wait 5 minutes for the gas to clear, and then try match-lighting the side burner. Match Lighting - Side Burner CAUTION Use a LONG wooden match, match extension, or butane lighter with extension....
Este manual também é adequado para os modelos :Greeley - 8450 Series (2.03 mb)