Assessments - , GPA:
(
)
)
Fabricante : Coleman
Arquivo Tamanho: 1.48 mb
Arquivo Nome : d5841027-82ca-4d98-92fc-260165e39888.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
Do not use another hose and regulator assembly other than the one supplied with the grill or a Coleman® replacement pressure regulator assembly. The pressure regulator and hose assembly provided is factory set at an outlet pressure of 11 inches water column (1/2 psi). • Keep the small vent hole in the regulator clean of dirt and debris (see item [G], Fig. 1). • Consult your L.P. gas dealer if you think the regulator is not working properly. WARNING During assembly of the grill and when attaching or replacing the L.P. gas cylinder, insure that the gas supply hose is free of kinks and/or damage and is at least 3 inches away from hot surfaces such as the grill housing. Transporting the Cylinder • Transport only one cylinder at a time. • Transport the cylinder in an upright and secure manner with a control valve turned off and the cap in place. • DO NOT transport the cylinder in the passenger compartment, unless you have an open window ventilation. • DO NOT leave the cylinder in direct sunlight or in a high heat area such as a closed car trunk. High heat areas could cause the relief valve to vent gas. • Use a cylinder cap on the cylinder valve outlet during transport and when the cylinder is not connected to the grill. • Keep the cylinder valve closed when not in use. • Take the cylinder directly home after it has been filled. 5 WARNING Handle a full cylinder with care. Gas is under high pressure. DANGER • NEVER store a spare L.P. gas supply cylinder under the grill body or inside the grill enclosure or in the vicinity of any heat producing appliance. (Fig. 3) • NEVER fill the cylinder beyond 80% full. Failure to follow this information exactly could result in an explosion and/or fire causing death or serious injury. CAUTION Purging and Evacuating Devices for L.P. Gas Cylinders with Type 1 Cylinder Valves CGA-510 POLFig. 4 WARNING Handle a full cylinder with care. Gas is under high pressure. DANGER • NEVER store a spare L.P. gas supply cylinder under the grill body or inside the grill enclosure or in the vicinity of any heat producing appliance. (Fig. 3) • NEVER fill the cylinder beyond 80% full. Failure to follow this information exactly could result in an explosion and/or fire causing death or serious injury. CAUTION Purging and Evacuating Devices for L.P. Gas Cylinders with Type 1 Cylinder Valves CGA-510 POLFig. 4 Filling and Purging Type 1 Transporting the Cylinder (continued) L.P. Gas Cylinders (continued) Fig. 3 REPRESENTATIVE ILLUSTRATION Filling and Purging Type 1 L.P. Gas Cylinders Take these instructions to the L.P. gas dealer. DANGER Purging and filling of L.P. Gas cylinders must be performed by personnel who have been thoroughly trained in accepted L.P. Gas industry procedures. Failure to follow this instruction may result in explosion, fire, serious personal injury, or death. • When using cylinder exchange: If your grill is equipped with a Type 1 cylinder, be sure the exchanged cylinder is a Type 1 cylinder, as a 510 POL cylinder will not fit Type 1 regulator. • This tank is easily filled with a standard CGA 510 POL filling connection. (Fig. 4) • New cylinders must be purged before filling. Tell your L.P. Gas dealer if your cylinder is new and has not been previously filled. The L.P. Gas cylinder has a Type 1 cylinder valve with a back- check module in its outlet which will not permit gas to flow until an evacuation device is installed. To purge the L.P. Gas cylinder, the back-check module must be opened with an evacuation device. After purging or filling an L.P. Gas cylinder, DO NOT insert a POL plug into the valve outlet. Insertion of the plug will prevent the back-check from closing. Use ONLY the provided cap and strap attached to the outlet. Close the cylinder valve knob before returning the cylinder to the customer. For proper purging procedures refer to: In the US: Safety Bulletin NPGA# 133, “Purging L.P. Gas Cylinders”, and Safety Bulletin NPGA #130, “Recommended Procedures for Filling Cylinders”. A. Hose end valve with a bleed port (Fig. 4): Purging can be accomplished using a hose end valve containing a bleed port which also allows for evacuation without the use of an adapter. B. Hose end valve without a bleed port: When a hose end valve does not have a bleed port, a separate device must be used for evacuation. C. Purging using a Type 1 connection (Fig. 5): L.P. Gas cylinder evacuation can be accomplished during each purging by using a Type 1 connection. The Type 1 valve outlet has an external 1 5/16" ACME right-hand thread which will accept this connection. TYPE 1 Fig. 5 6 1 3 4 6 7 8 9 10 11 2 Grill Features — 8300 Series 13 14 12 5 1 3 4 6 7 8 9 10 11 2 Grill Features — 8300 Series 13 14 12 5 1. Grill Hood 2. Thermometer 3. Hood Handle 4. Control Knob: Side Burner 5. Right Side Shelf 6. Electronic Igniter: Main, Side, and Rear Infrared Burner. 7. Convection Vents 8. Cart with Doors 9. Control Knobs: Main Burners 10. Control Knob: Rear Infrared Burner 11. Left Side Shelf 12. Grilling/Coo...