Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
In Canada, the electrical accessory must be electrically grounded in accordance with the applicable section of the current Canadian Electrical Code, CSA C22.1. Any electrical accessory should be equipped with a three-prong (grounding) plug, and plugged into a properly grounded three-prong receptacle or wall outlet. Do not cut or remove the grounding prong from the plug. If an extension cord is required, use only a three-prong cord and plug into a properly grounded receptacle as described above. Do not expose an electrical accessory to water. Avoid using any electrical accessory in wet weather as it may present a shock hazard. Keep any electrical cord and fuel supply hose away from all heated surfaces. B101623-2-0112 MAINTENANCE Venturi Tubes The venturi tubes allow air and gas to mix prior to burning, thus ensuring an efficient flame. Spiders or other small insects may build webs or nests inside the tubes obstructing air flow. Fire, or flashback, can occur, in and/or around obstructed venturi tubes and can cause damage to components beneath the grill or an unsafe condition. To reduce risk, inspections and cleaning should be performed at least twice monthly when spiders are active. If the grill has been unused for an extended period of time inspect the tubes before using the grill. Clean venturi tubes as follows: 1. Remove the cooking grids and briquette rack. 2. Remove the burner from the grill. 3. Lay the burner face down and remove the four retaining screws from the venturi tube plate and the burner. See Figure 23. 4. Use a small flexible brush to remove any debris for the tube(s). 5. Flush with water. 6. Allow the tube(s) to dry before reinstalling. 7. Reinstall the venturi tubes and burner. Cleaning the Grill Caution: To prevent injury, use care when cleaning a hot grill. Note: Do not use a commercial cleaner on the cooking grid. Do not brush grids while they are hot. Do not scrape grids. For baked on residue use a brass (NOT STEEL) brush on the cooking grid and other components. Burn Off This process is much like that used in self-cleaning ovens and is most efficient when completed after each use of the grill. Caution: Do not open the grill during the burn off process. Opening the grill during the burn off process may cause a sudden grease fire flare up that could burn your face and arms. Wait until the grill has cooled before opening. 1. Turn gas knob to HI. Close lid and allow the grill to burn for ten minutes, or until no smoke is present. Do not allow the grill to burn for more than 30 minutes. 2. Turn gas knob and supply to OFF and allow the grill to cool. 3. Wipe COOL grill with a damp cloth to remove soot. Grill Bottom Periodically remove cooking grids and flare guard to clean the interior of the grill. Scrape off baked on residue with a putty knife or brass brush and rinse with water. Clean the bottom air holes with a small knife. Burner Maintenance Stainless steel burners often turn reddish brown after use. This does not effect the performance of the grill. When cleaning the interior of the grill, remove the burners and clean with a brass brush. Wash with water and a mild detergent. Grease Cup Empty periodically. Figure 23 Note: Bowtie burner is shown. Follow the same steps for the H burner assembly. Exterior Clean regularly with a solution of mild detergent and hot water. Touch-up paint is available from your dealer. Broilmaster® protective covers are recommended. Stainless steel components can be easily cleaned with a spray-on stainless steel cleaner found in most hardware stores. Briquettes If the briquettes did not come clean during burn off, after cooling turn them over. The residue will burn off during warm-up for the next use. B101623-2-0112 TROUBLESHOOTING Although the manufacturer has attempted to ensure that your grill will operate properly and satisfactorily, sometimes problems do arise. The following troubleshooting guide lists several possible problems and their probable cause and solution. Problem Cause Solution Burner will not light. Gas injector not inserted in venturi tube. Realign/engage gas injector with the venturi tube. Clogged gas injector. Remove gas injector from gas control assembly and clean. Obstruction in gas line. For propane models, ensure gas valve on cylinder is OFF. Remove flexible hose and blow out any debris. Spider webs in venturi tubes. Clean venturi tubes. See Maintenance Section. Misalignment of collector box and burner. Position electrode properly. Clean collector box. Out of gas Refill LP gas cylinder. If natural model, turn on gas at source. Dead battery. Replace with AA Alkaline battery. Inadequate grill temperature. Poor combustion. Adjust air shutter. Misalignment of venturi tube and gas injector. Realign/engage gas injector with the venturi tube. Inadequate gas pressure. Contact gas supplier for assistance. Incorrect orifice/valve setting. Refer to gas conversion instructions in this manual. Flames blow out. Cold grill. Preheat grill at least 5 min...
Este manual também é adequado para os modelos :Greeley - H3X-1 (9.89 mb)
Greeley - H3XN-1 (9.89 mb)
Greeley - H3XPK-1 (9.89 mb)
Greeley - H4PK-1 (9.89 mb)