Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Stainless steel surfaces may be cleaned with a spray- on stainless steel cleaner available at most hardware stores. Important: Do not use harsh or abrasive cleaners! Your post has a highly polished surface and may be easily scratched. PERIODIC INSPECTION AND MAINTENANCE Periodic inspections and maintenance are essential. All Broilmaster Gas Grill products or mechanical devices eventually begin to wear due to environment, contaminants, corrosion or aging. Inspect all components at least twice per year and replace any that show wear. If any parts are damaged or missing, you may order parts from your local Broilmaster dealer. Please refer to the Parts Diagram and Parts List section of this manual for more detailed information. Page 4 B101075-0-1006 B101075-0-1006 Page 5 All repair part orders should be placed through your local Broilmaster dealer. To locate a dealer in your area, contact Broilmaster Customer Service at 800-851-3153 • To ensure prompt and accurate service, please provide the following information when placing a repair part order: Model Number, Part Name, Part Number, and Quantity of parts needed. REMOVE PROTECTIVE COATING FROM STAINLESS STEEL PARTS STARTING AT POP RIVETS AND VERIFY THAT ALL PARTS LISTED IN THE EXPLODED VIEW ON THIS PAGE HAVE BEEN INCLUDED BEFORE BEGINNING THIS INSTALLATION. CAUTION: USE CAUTION WHEN HANDLING PARTS, AS THEY MAY CONTAIN SHARP EDGES. WORK GLOVES ARE RECOMMENDED TO PREVENT INJURY. PATIO BASE PARTS LIST & EXPLODED VIEW Key Number Part Name Quantity BPB26 Part Number SSPB26 Part Number 1 9/32 I.D. x 5/8 O.D. Flat Washer 13 B100136 B100136 2 1/4 Lock Washer 16 B100139 B100139 3 1/4-20 Hex Nut 16 B100120 B100120 4 1/4-20 x 1 3/4" Eyebolt 4 B100118 B100118 5 1/4-20 x 3/4" Bolt 8 B100115 B063096 6 Control Housing 1 B101076 B101060 7 26" Square Post 1 B878517 B070283 8 1/4-20 x 4" Eyebolt 4 B100111 B100111 9 Cast Iron Patio Base 1 B074604 B074604 10 Grease Cup Bracket Assembly 1 B100545 B100545 NS #10-24 Wing Nut 2 B100125 B100125 NS #8 x 1/2" Phillips Truss Screw 2 B100132 N/A NS Fastener Panel - Plastic 2 N/A B068182 NS Stainless Steel Flex Tube Assembly 1 B076518 B076518 NS Male Flare Fitting 1 B100100 B100100 NS #10-24 x 3/4" Bolt 1 B100128 B100128 NS Grease Cup 1 B100526 B100526 6 5 4 1 2 3 10 5 3 2 8 9 1 1 3 2 7 Page 6 B101075-0-1006 The BPB26 and SSPB26 Patio Base are only for use with Broilmaster Gas Grills. Before proceeding with installation read the Owner’s Manual for the proper location and minimum clearances to combustible materials for your grill and patio base. Verify that all parts listed in the exploded view of this product have been included before beginning this installation. Recommended Tools: • Two adjustable wrenches or a socket set • A medium Phillips screwdriver • Pipe thread sealer or Teflon tape (for gas connections) • Soapy water solution (to test for leaks) Attach four 1/4-20 x 4" eyebolts (8) to the bottom of the 26" square post (7) using 1/4 - 20 x 3/4" bolts (5), 9/32 ID x 5/8 OD flat washers (1), 1/4 lock washers (2), and 1/4-20 hex nuts (3). Figure 1. NOTE: The large rectangular cut out is located at the front of the post near the top. Fasten the bottom of the post to the cast iron patio base (9) using 9/32 ID x 5/8 OD flat washers, 1/4 lock washers, and 1/4-20 hex nuts. FIGURE 2. Anchor the cast iron patio base to your patio using the two holes provided in the base. (Hardware not included) Note: Make sure that the large rectangular cut out is facing in the direction that you want your grill to face. FIGURE 2. Insert the stainless steel flex tube assembly into the post. The inlet side of the gas tubing may protrude from the bottom of the patio base or through the large circular hole in the back of the square post. Note: Do not attempt to cut or alter the flex tube in any way. PATIO BASE ASSEMBLY 1 2 3 Figure 1 Figure 2 B101075-0-1006 Page 7 Arrange with your local gas company or licensed contractor to have a gas supply line connected to the inlet of the stainless steel flex tube assembly. The gas supply must have a shutoff valve inside the wall and must be shutoff when the grill is not in use. Use pipe thread sealant or Teflon tape at the threads of each connection being careful to not allow any of these materials into the flare seat. Test for gas leaks as directed by the grill’s Owners Manual. The grill and its individual shutoff valves must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 PSIG.The grill must be isolated from the gas supply piping system by closing its individual manual shutoff valves during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG. WARNING: DO NOT SUPPLY LP GAS TO A GRILL DESIGNED FOR NATURAL GAS OR NATURAL GAS TO A GRILL DESIGNED FOR LP GAS. Gas leak tests should be completed as directed in the grill owner's manual. Fasten the four 1/4-20 x 1 3/4" eyebolts (4) to...