Assessments - 5, GPA: 4.4
(
)
)
|
Facilidade de uso
Omitting the baffle can result in unacceptable burner combustion. . Inspect all gaskets. Replace any that are damaged or would fail to seal adequately. . Clean the blower wheel, air inlet, air guide, retention head and static plate of any lint or foreign material. . If motor is not permanently lubricated, oil motor with a few drops of SAE 20 nondetergent oil at each oil hole. DO NOT over oil motor. Excessive oiling can cause motor failure. . Check motor current. The Amp draw should not exceed the nameplate rating by more than 10%. . Check all wiring for secure connections or insulation breaks. . Check the pump pressure and cutoff function. . Check primary control safety lockout timing. . Check ignition system for proper operation. . Inspect the vent system and chimney for soot accumulation or other restriction. . Clean the appliance thoroughly according to the manufacturer's recommendations. . Check the burner performance. Refer to the section “Set combustion with instruments.” It is good practice to make a record of the service performed and the combustion test results. To replace blower wheel: 1. Turn off all power to the burner before servicing. 2. Disconnect the wires to the burner motor. 3. Remove the bolts securing the blower motor to the housing. 4. Remove the blower motor and wheel. 5. Remove the existing wheel. 6. As shown at right, slide the new blower wheel onto the shaft. • Place a .030" (1/32" ± 1/64") feeler gauge on the motor as shown. • Slide blower wheel toward motor until it contacts feeler gauge. • Rotate the wheel until the set screw is centered on the flat of the motor shaft. • Tighten the set screw to secure the wheel. 7. DO NOT use a motor that has endshield openings outside the blower wheel circumference represented by the dashed line. 8. Install the motor on the burner housing. Tighten screws. Reconnect motor wires. 9. Restore power, start the burner and perform combustion tests. Refer to “Set combustion with instruments. ” Instruction Manual – Model AFG Oil Burner 11 Replacement parts Awaiting new info Service & maintain burner Instruction Manual – Model AFG Oil Burner Service & maintain burner Owner’s information This burner must be installed, adjusted and started only by a qualified service agency — an individual or agency, licensed and experienced with all codes and ordinances, who is responsible for the installation and adjustment of the equipment. • Have your equipment inspected and adjusted at least annually by your qualified service agency to assure continued proper operation. • Installation and adjustment of the burner requires technical knowledge and the use of combustion test instruments. Do not tamper with the unit or controls. Call your qualified service agency. • Incorrect operation of the burner could result in severe personal injury, death or substantial property damage. The following could result in fire hazard, severe personal injury, death or substantial property damage. Read carefully. • Never attempt to use gasoline in your heating appliance. • Never store gasoline or combustible materials near the burner or appliance. • Never attempt to burn garbage or refuse in your appliance. • Never attempt to light the burner/appliance by throwing burning material into the appliance. • Never attempt to use crankcase or waste oil or material other than the approved fuel oils in this burner. • Never restrict the air inlet openings to the burner or the combustion air ventilation openings in the room. Owner service and maintenance Properly installed and maintained, your AFG burner will provide years of efficient, trouble-free operation. Please take care of your equipment by following the warnings provided and by doing the following (notify your qualified service agency if you find anything wrong): Annually (minimum) • Have your burner/heating appliance serviced at least annually by your qualified service agency as noted above. Daily • Check the room in which your burner/appliance is installed. Make sure: • air ventilation openings are clean and unobstructed • nothing is blocking the burner inlet air openings • no combustible materials are stored near the heating appliance • there are no signs of oil or water leakage around the burner or appliance. Weekly • Check your oil tank level. Always keep your oil tank full, especially during the summer, in order to prevent condensation of moisture on the inside surface of the tank. Warranty Beckett warrants its equipment specifically to those who have purchased it for resale, including your qualified service agency (dealer). In the event of any problems with your equipment or its installation, you should contact your dealer for assistance. The OilHeat Manufacturers' Association supports the use of low sulfur fuels as defined by ASTM D396, Grades Number 1 Low Sulfur and Number 2 Low Sulfur, as the preferred heating fuel for the following reasons: • Low sulfur fuels reduce deposits on heat exchanger surfaces, extending the service interval...