Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Lay cardboard down to protect grill finish and assembly area. CAUTION! Some parts may contain sharp edges. Wear protective gloves if necessary. Step 1 Remove the two bolts from the top corner of the back panel. With the help of a friend, lift the back panel out and take it to a clear area. Remove all the parts boxes from the base. Note: Keep these two bolts, do not throw them away. They will be used in Step 3. Back Panel Bolts Step 2 Add six M6 x 12mm bolts to the middle grill base bracket as illustrated and tighten securely. Guide Pin Extension Cord Hole Step 3 With the help of a friend, attach the back panel to the Grill Island base by using ten M6 x 12mm bolts. First, align the two holes to the guide pins which are located at the bottom of the island base. Note: This will include the two bolts which come from Step 1. 22 Back Panel Bolts Back Panel Bolts 23 Step 4 Attach the side burner support bracket onto right side of the grill island by using four M6 x 12mm bolts. Note: Make sure the arrow is facing to front. Step 5 Attach the grill support bracket onto left side of the Grill Island by using four M6 x 12mm bolts. Note: Make sure the arrow is facing to front. Step 6 Insert M8 full thread studs into the bottom of the granite tops. Total of fourteen studs to three granite tops. 24 Step 7 Attach the granite tops by aligning the M8 threaded studs into the rubber ringed holes which are located on the top of the Grill Island base. Secure granite top to base using round washers and M8 nuts applied to each threaded stud.(Hand tighten only) Note: Before attaching the back granite piece turn support plates 90 degrees. Note: After granite top installation, seams can be filled with clear silicone caulk for a more finished appearance. Threaded Stud Washer M8 Nut Support Plates Support Plates Note: Lift the side burner from front and rear panels to avoid injury to hands and fingers. Step 8 Attach the side burner onto the right side of the grill base. Align the side burner bottom bar to the tracks on the side burner support, then slide it backward until it locks in place. Step 9 Then pull the hose out from the hole which is located at the left side of the side burner assembly. Tracks Side Burner Bottom Bar Middle Grill Base Bracket Tracks Rock Fascia 26 Step 10 Attach the grill body side trim to the grill side end cap by using two M6 x 12mm bolts. Repeat for other end cap. Step 11 With the help of a friend, (we recommend 3 to 4 people to assembly the grill body) place grill body assembly on Grill Island. Make sure the hose and coupler fitting will pass through the front gap between the front panel and grill body support bracket. Then align the two holes at the bottom front grill bracket to the grill support bracket, then tighten securely by using two M6 x 12mm bolts. Step 12 Route the hose through the opening in the back panel for connection to the quick-disconnect coupler. M6 x 12mm bolt Step 13 Remove pre-cut granite plug and insert rotisserie motor cord through opening. Step 14 Slide rotisserie motor onto the rotisserie motor bracket. Replace granite plug into granite top. Step 15 Feed extension cord (not provided) through back panel of base unit and up through inside of grill cabinet base hole. Plug rotisserie motor cord into extension cord plug. 28 Step 16 Connect the side burner hose to the grill body hose by inserting the fitting into the quick connect coupler. Step 17 Insert hinge pin in bottom of left side door into hole at the bottom left door frame then align door with left side door frame. Depress spring pin located on top edge of door and slide door toward left side door frame until spring pin locks into hole in door frame. Repeat for other door. Step 18 To attach the door handle to the door, insert four M6 x 12mm bolts halfway onto the door handle stand. Align the bolts to the keyholes which are located on the door panel, and slide down. Then tighten the four bolts securely. Repeat for other door. Step 19 Attach basket bracket guide using two M5 x 10mm bolts. Step 20 Place the basket into the basket brackets and basket guide. Then fasten it by using a M6 nut, and tighten securely using small hex nut wrench. Spring Pin Hinge Pin M6 Nut Step 21 Insert main burner grease tray into opening on front side of main burners. Step 22 Insert side burner grease tray into opening on front side of side burner. Step 23 Remove the side burner igniter cap and insert battery with positive end of battery toward igniter cap. Replace igniter cap and make sure the igniter is working properly. Repeat for grill burner igniter. SIDE BURNER 30 Step 24 Place side burner grate on side burner. Step 25 Place the four heat distribution plates on tabs which are located on the lower level of grill body assembly directly above burners. Step 26 Place stainless steel cooking grills on support ribs directly above heat distribution plates. Step 27 Place warming rack in slots above the stainless steel cooking grills. 31 Charmglow Grill Islan...