Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Make sure door hinge pins are on the top side and facing the front. Secure using two 1/4-20x1.” screws, 7mm lock washers, and 7mm flat washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED IN THE MOST DOWNWARD POSITION WHEN ASSEMBLED TO CART. Door Hinge Pin Front brace Control panel 7mm flat 7mm lock 1/4-20x1.” washer washer screw 10Attach right and Insert left and right grease tray rails into slots beneath grease tray opening in upper back panel, shown A. left rails under front brace with two #8x3/8” self-tapping screws, shown B. Right rail Left rail Grease tray opening A Front Brace Right railLeft rail #8x3/8” self-tapping screw B 1111 Insert hinge pin on bottom of door into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top ofdoor, and release hinge pin into door. Hinge pin on bottom of door Top ofdoor PRESS Door 12 Release the cap and nut from electronic ignition module. Attach electronic ignition module to the cart right side panel with the nut and cap, shown A. Connect each of the wires from the main burner electrodes into the back of the Electronic Ignition Module. Total (2) connections. Connect the two wires [(A) and (B)] from the switch wiring harness into the back of the Electronic Ignition Module. Total (2) connections. NOTE: Switch terminals are larger than electrode terminals and should only be installed in location shown as (A),(B). Wire 1 2 (A) (B) Right side panelignition module Electronic ACapNut 1313 Install flame tamers by sliding one end of each flame tamer into slots at front of firebox and resting opposite end on pins in back of firebox. Back of firebox Front of firebox Flame tamers Pin 14 Place cooking grates onto the firebox as shown. Insert the two wire ends at rear of warming rack into holes in back offirebox. Front wires of warming rack rest on sides of firebox. 20 Assembled warming rack Warming rack Cooking grate 1515 On back of grill, slide grease tray into opening in upper back panel. CAUTIONFailure to install grease tray willcause hot grease to drip from bottomof grill with risk of fire or propertydamage. Grease tray 16 . Unscrew electronic ignition cap on cart right side panel. Insert AA battery into ignitor, negative (—) end first. Replace the cap. AA Battery Electronic Ignition Cap +- 17 1717 LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care section). Once cylinder has been filled and leak checked, place cylinder into hole in bottom shelf. Make sure cylinder valve is facing front of grill. Secure cylinder with cylinder screw under bottom shelf. See Use & Care section of this manual to perform the “Burner Flame Check” and for important safety instructions before using. Cylinder screw at rear of cart Cylinder screw Always keep LP cylinders in upright position duringuse, transport, and storage. – CAUTIONRegulator LP Cylinder( not included) Cylinder valve must face to front of cart oncetank is attached. Failure to install cylindercorrectly may allow gas hose to be damaged in operation, resulting in the risk of fire. EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Possible Cause Prevention/Solution Gas leaking fromcracked/cut/burnedhose. Gas leaking from LPcylinder. Gas leaking from LPcylinder valve. Gas leaking betweenLP cylinder and regulator connection. Fire coming throughcontrol panel. Grease fire or continuous excessive flames above cookingsurface. • Damaged hose. • Mechanical failure due to rusting ormishandling. • Failure of cylinder valve frommishandling or mechanical failure. • Improper installation, connection nottight, failure of rubber seal. • Fire in burner tube section of burner due to blockage. • Too much grease buildup in burner area. • Turn off gas at LP cylinder or at source on natural gas systems. If anything but burned, replace valve/hose/regulator. If burned, discontinue use of product until a plumber has investigated causeand corrections are made. • Replace LP cylinder. • Turn off LP cylinder valve. Return LP cylinder to gas supplier. • Turn off LP cylinder valve. Remove regulator from cylinder and visually inspect rubber seal for damage. See LP Cylinder Leak Test and Connecting Regulator to the LP Cylinder. • Turn off control knobs and LP cylinder valve. Leave lid open to allow flames to die down. After fire is out and grill is cold, remove burner and inspect for spider nests or rust. See Natural Hazardand Cleaning the Burner Assembly pages. • Turn off control knobs and LP cylinder valve. Leave lid open to allow flames to die down. After cooling, clean food particles and excess grease from inside firebox area, grease tray, and other surfaces. Troubleshooting Problem Burner(s) will not lightusing ignitor. (See Electronic IgnitionTroubleshooting also) Continued on next page. Possible Cause GAS ISSUES: • Trying to light wrong burner. • Burner not engaged with control va...