Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
However, the method of assembly remains the same. PARTS DIAGRAM PARTS DIAGRAM SEFQDBAJJIZLCKBBEEFFGGDDNOTKKUSSPPVVBGHJMPRSSSTTAAOOQQRRIIHHIIMMNNCCYVXUULLWWWTTXX ASSEMBLYASSEMBLY 1 Place bottom shelf upside down. Insert Bent U Pin into the caster mounting plate to lock it in place, shown A. Spin the caster clockwise into the threads on the bottom shelf until secure. Remove the Bent U Pin and repeat for remaining casters. Make sure the two locking casters are secured at the rear and the non-locking casters are secured at the front. After all 4 casters are secure remove the Bent U Pin and save for future maintenance. Locking caster Bottom shelf Fixed caster RearFrontABent U pin 2 Make sure side panelsare pushed as far to therear of bottom shelf as possible before fullytightening screws. 1/4-20x1/2” screw Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel. IMPORTANT: Panel with large hole mustBe on left side of bottom shelf. 7mm lock washer 7mm flat washer Left side panel(with large hole) Right side panel Rear 33 Attach front brace to side panels using two #10-24X1/2” screws, 5mm lock washers and 5mm flat washers on each side. Magnet 5mm flat washers 5mm lock washers #10-24x1/2” screws Rear 4 Attach rear cart brace to cart frames using two #8-32x3/8” screws, 5mm lock washers and 5mm flat washers on each side. 55 Insert wire ends on lower tank exclusion wire into bottom shelf (A). Attach with two #8-32x3/8" screws diagonally. Place upper tank exclusion wire on front brace and back brace as shown, secure with two #8-32x3/8" screws and #8-32 flange nuts (B). Magnet Front brace #8-32x3/8" screw #8-32 flange nutUpper tankexclusion wire Lower tank exclusion wire 6 Two #8-32x3/8" machine screws are installed partially in the cart side panel. Slide door hinges onto the screws as shown. Secure right door with four #8-32x3/8" machine screws. Repeat assembly for left door. #8-32x3/8” machine screws This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart. Make sure the regulator hose is hanging outside the cart. Insert 1/4-20x1/2" screws through side panels and firebox in all four corners. Secure with fiber washers and 1/4-20 flange nuts. 1/4-20x1/2" screw Fiber washer 1/4-20 flange nut Mount fascia onto side shelf using three #10-24x1/2" screws, 5mm lock washersand 5mm flat washers (A). Hang side shelf on the tabs mounted on the firebox. Secure shelf brackets to cart side panel using two 1/4-20x1/2" screws, fiberwashers and 1/4-20 flange nuts on each bracket (B). Secure fascia to firebox using two 1/4-20x1/2" screws, 7mm lock washers and 7mm flat washers (C). CAUTION SHARP EDGES! Wear gloves if necessary CRepeat on front bracket 1/4-20x1/2" screw 1/4-20 flange nut Fiber washer Lock washer Flat washer #10-24x1/2" screw Repeat on left side shelf Flat washer Lock washer 1/4-20x1/2" screw Side shelfHook side shelf into inside edge Repeat step 7 (A) on left side shelf. Hang sideburner shelf on tabs mounted on the firebox. Secure shelf brackets to cart side panel using two 1/4-20x1/2" screws, fiber washers and 1/4-20 flange nuts on each bracket (A). Secure fascia to firebox using two 1/4-20x1/2" screws, 7mm lock washers and 7mm flat washers (B). Afiber washer 1/4-20x1/2”screw flange nut B7mm flat washer 7mm lock washer 1/4-20x1/2” screw CAUTIONSHARP EDGES! Wear gloves if necessary. ARepeat step 7 (A) on left side shelf. Hang sideburner shelf on tabs mounted on the firebox. Secure shelf brackets to cart side panel using two 1/4-20x1/2" screws, fiber washers and 1/4-20 flange nuts on each bracket (A). Secure fascia to firebox using two 1/4-20x1/2" screws, 7mm lock washers and 7mm flat washers (B). Afiber washer 1/4-20x1/2”screw flange nut B7mm flat washer 7mm lock washer 1/4-20x1/2” screw CAUTIONSHARP EDGES! Wear gloves if necessary. A Place drip pan onto sideburner shelf. Secure with #10-24x 1/2" screws, insulation washers, 5mm flat washers, 5mm lock washers , #10-24 hex nuts, #10-24x 1/2” screws, 5mm lock washers, 5mm flat washers and side burner lid supports. 21 #10-24 x ." Screws Insulation Washers 5mm Flat Washers 5mm Lock Washers #10-24 Hex Nut 5mm Flat Washers 5mm Lock Washers #10-24 x ." Screws Sideburner lid supports 1111 Remove two #8-32x3/8" screws from sideburner valve bracket. From behind the fascia, place sideburner valve bracket into hole. Attach bezel to valve with #8-32x3/8" screws. Press sideburner control knob onto valve stem. Control knob Control knob bezel Sideburner valve bracket 12 Insert sideburner into sideburner drip pan (A), make sure burner tube engages with sideburner valve. Illustration (B) shows correct burner-to-valve engagement. Center stud on bottom of sideburner fits into center hole in sideburner drip pan. Secure with one wingnut (C). Connect sideburner ignitor wire to sideburner electrode. 22 Burner tube Valve BElectrode Sideburner ignitor wire CASideburner Place sideb...