Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
You may also have other rights which vary from state to state. In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling this product or the Manufacturer will refund the purchaseprice paid for the product, less the amount directly attributable to use by the original consumer-purchaser prior todiscovery of the nonconformity. In addition, in the state of California only, you may take the product to the retail establishment selling this product in order to obtain performance under this limited warranty. If you wish to obtain performance of any obligation under this limited warranty, you should write to: Consumer Relations P. O. Box 1240 Columbus, GA 31902-1240 Consumer returns will not be accepted unless a valid Return Authorization is first acquired. Authorized returns are clearlymarked on the outside of the package with an RA number and the package is shipped freight/postage pre-paid. Consumer returns that do not meet these standards will be refused. PARTS LIST PARTS LIST Not Pictured Key Qty Description A 1 FIREBOX B 1 VALVE/HOSE/REGULATOR C 1 CONTROL PANEL D 2 CONTROL KNOBS E 1 IGNITOR F 2 AXLE F/WHEEL G 1 LEFT CART LEG H 1 BURNER ASSEMBLY I 2 WHEELS J 1 RIGHT CART LEG K 2 LEG EXTENDER L 1 BOTTOM SHELF M 1 BACK SUPPORT BRACE N 1 TANK RETAINER O 1 FRONT PANEL P 1 SIDE SHELF Q 1 LID R 1 LOGO PLATE ASSEMBLY S 1 HANDLE ASSEMBLY T 1 SIDEBURNER FRAME U 1 SIDEBURNER PAN V 1 SIDEBURNER GRATE W 1 TOOL HOLDER X 1 SIDEBURNER VALVE CUP Y 1 SIDEBURNER Z 1 SIDEBURNER KNOB AA 1 HEAT TENT BB 1 COOKING GRATE CC 1 SWING AWAY DD 2 LOWER HINGE EE 2 UPPER HINGE FF 1 GREASE CUP GG 1 CLIP, GREASE CUP HH 1 HEAT SHIELD F/TANK II 1 HEAT SHIELD F/FIREBOX JJ 1 MATCH HOLDER … 1 PRODUCT MANUAL, ENGLISH … 1 PRODUCT MANUAL, SPANISH … 1 HARDWARE PACK NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the method of assembly remains the same. PARTS DIAGRAM PARTS DIAGRAM QEEHRCCDDSBBAAAVUTPYZWMCGINEDGGFFJLOXBHHIIFFJJ K #10-24 Plastic Wing NutsQty.2 “Cone” side of wheel against leg #10-24 X 2” Carriage BoltQty.2 1” Hitch Pin Qty.2 Axle Bolt Qty.2 Right Leg Assembly Left Leg Assembly Wheel Bottom Shelf Leg Extender #10-24 Plastic Wing NutsQty.2 “Cone” side of wheel against leg #10-24 X 2” Carriage BoltQty.2 1” Hitch Pin Qty.2 Axle Bolt Qty.2 Right Leg Assembly Left Leg Assembly Wheel Bottom Shelf Leg Extender ASSEMBLY 1 A Attach right leg assembly to bottom shelf with (2) #10-24x2" carriage bolts and #10-24 Plastic wing nuts. B Push Leg Extenders into the bottom of the right legs. C Place left leg assembly into bottom shelf. Insert axle bolts into wheels, legs and bottom shelf. Secure with hitch pins. 2 Attach back support brace to legs with (4) #10-24x2" carriage bolts and #10-24 Plastic wing nuts. #10-24 X 2” Carriage BoltQty.4 #10-24 Plastic Wing NutsQty.4 Back Support Brace 33 A Place bottom of front panel into three slots in the bottom shelf. B Attach front panel to legs with four #10-24x2" machine screws and #10-24 flange nuts. #10-24 Flange Nut Qty.4 #10-24 X 2” Machine Screw Qty.4 Back of Cart 4 Place valve/hose/regulator onto control panel. Attach with #10-24 x .” machine screws. NOTE: Make sure the two valve stems are centered in their clearance holes; otherwise, this can cause main burner level problems. Attach ignitor to control panel using the stamped nut that's provided. NOTE: if your grill come with Snap-in ignitor, please see Option. #10-24 x .” Machine Screw Qty.2 Valve/Hose/Regulator Ignitor Snap-inIgnitor Valve/Hose/Regulator Option: Snap theignitor into the control panel. Stamped Nut 55 Attach control panel to firebox using #10-24 x .” machine screws, silicon washers and #10-24 flange nuts. Firebox #10-24 x .” Machine Screw Qty. 4 Silicon Washer Qty. 4 #10-24 Flange Nut Qty. 4 Control Panel 6 A Place firebox onto cart, make sure the regulator hose hangs inside cart and control panel overlaps front panel.Attach to cart with #10-24x1-1/4" machine screws, Silicon washers and #10-24 flange nuts. B Place burners assembly into firebox, making sure valves are inside the burner tubes. Attach to firebox with #10-24 x .” machine screws and silicon washers. C Attach wire of main burner to ignitor. Burner Assembly #10-24 x .” Machine Screws Silicon Washer #10-24 Qty. 2 Qty: 6 Flange Nuts Qty. 4 #10-24x1-1/4" Machine Screw Qty: 4 Correct burner-to-valve engagement Firebox Front Panel ABC Sideburner Knob CSideburner Knob C 7 Tool Holder Sideburner Frame Metal Wing Nut Flange Nut T-WingScrew Sideburner Pan #10-24x2" Carriage Bolt A Attach tool holder to front leg using two #10-24x2" machine screws and #10-24 flange nuts. Place sideburner pan into frame and attach with a #10-24x2" carriage bolt and #10-24 metal wing nut in back and a T-wing screw in front. B Attach sideburner valve cup. Place sideburner into hole. Make sure side burner valve is inside sideburner tube. Fasten sidebur...