Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Make sure door hinge pins are on the top side and facing the front. Secure upper holes using one 1/4-20x1%" screw and fiber washer on each side. Secure lower holes using one 1/4-20x1%" screw on each side. 6 On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel in lower holes using one 1/4-20x1%" screw and fiber washer on each side. Do not fully tighten screws until side shelf installation is complete in later steps. 15 7 Attach right side fascia to right side shelf using four #10-24x3/8" screws,5mm lock washers and 5mm flat washers, shown A. Insert flange on right side shelf into side shelf brackets on right side of firebox, shown B. Attach right side shelf using two 1/4-20x3/4" screws and 1/4" nut, shown C. . Attach front of shelf using two #8x3/8" self-tapping screws and large flat washers, shown D. Attach rear of shelf using one 1/4-20x1%" screw, shown E. 16 8 Attach left side fascia to left side shelf using four #10-24x3/8"screws, 5mm lock washers and 5mm flat washers, shown A. Insert flange on left side shelf into side shelf brackets on side of firebox, shown B. Attach left side shelf using two 1/4-20x3/4” screws and 1/4” nuts, shown C. . Attach front of shelf using two #8x3/8” self-tapping screws and large flat washers, shown D. Attach rear of shelf using one 1/4-20x1%” screw, shown E. 17 9 First, remove the two screws and lock washers attached to the sideburner valve bracket. Position sideburner valve bracket beneath sideburner shelf fascia so that valve stem comes through larger center hole in fascia. Align the holes on valve bracket with left and right holes on fascia. Secure using screws and lock washers that were removed from bracket, shown A. Place sideburner bezel over valve stem on front side of fascia. Align small holes on bezel with upper and lower holes on fascia. Attach sideburner bezel to fascia using two #8-32x3/8" screws and 4mm lock washers. Press sideburner control knob onto valve stem, shown B. TA Screws and washers removed from valve bracket Sideburner shelf Note: Use left and right holes on fascia to attach valve bracket acket a \V t Sideburner shelf Fascia Note: Make sure to set the Bezel with the longer slot at the top. ote: Use upper and lower ' cia to attach bezel #8-32x3/8" screw 4mm Lock washer Sideburner Bezel 18 10 Insert sideburner into left shelf. The stud on bottom of the burner fits into the rear small hole in sideburner drip pan, shown A. Secure burner to sideburner drip pan with Wing nut, shown B. Under sideburner shelf, attach sideburner ignitor wire to electrode. Make sure burner tube engages sideburner valve, shown B. Place sideburner cooking grate onto sideburner shelf, aligning grate legs with holes in shelf, shown C. "CT Sideburner Grate 19 Connect each of the wires from the main burner electrodes, and sideburner electrode into the back of the Electronic Ignition Module.Total (4) connections. Connect the two wires[(a) and (b)] from the switch wiring harness into the back of the Electronic Ignition Module. Total (2) connections, shown A. Release the cap and nut from electronic ignition module. Attach electronic ignition module to the cart left side panel with the nut, shown B. Insert AA battery into ignition module, negative (-) end first. Then put on the cap, shown C. NOTE: Switch terminals are larger than electrode terminals and should only be installed in location shown as (a),(b). Electronic ignition module Cap AA battery 12 Inside of cart, insert rear tabs(w/o holes) of tank heat shield into slots on the bottom of upper back panel. Attach front tabs(w/holes) of tank heat shield under front brace using two #8x3/8" self-tapping screws. 20 13 Insert the pin on bottom of doors into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top of door, and release hinge pin into door. 21 15 Place cooking grates onto the firebox as shown. Place the Warming Rack onto the the firebox. Make sure insert the Warming Rack ends into the holes properly as shown. 16 LP TANK IS SOLD SEPARATELY. Fill and leak check the tank before attaching to grill and regulator (see Use & Care section). Once tank has been filled and leak checked, place cylinder into cut-out in bottom shelf. Make sure tank valve is facing front of grill. Secure tank with tank screw under bottom shelf. Insert regulator through large hole in right side panel. See Use & Care section of this manual to perform the "Burner Flame Check" and for important safety instructions before using. t CAUTION t LP Tank valve must face to front of cart once tank is attached. Failure to install cylinder correctly may allow gas hose to be damaged in operation, resulting in the risk of fire. Always keep LP tank in upright position during use, transport, and storage. 22 Consumer must purchase Natural Gas Conversion Kit 4584625 to convert this grill to natural gas. Use the following in...