Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
•Auto Power On Function* If you start iPod playback while your amp is on Standby, your amp will automatically turn on and select your iPod as the input source. Then, your iPod will start playback. •Direct Change Function* If you start iPod playback while listening to another input source, your amp will automatically select your iPod as the input source. •Timer Play You can use your amp’s Timer function to turn on your amp and iPod and start playback at a specified time. •Using Your Amp’s Remote Controller You can use your amp’s remote controller to control basic iPod functions (see page 16). Operating Notes: •The RI Dock must be connected to your amp with both an cable and an audio cable to use the functions. •If your amp doesn’t support the System On, System Off, Auto Power On, and Direct Change functions, you’ll need to turn your amp on and off and select the input source manually. •Before you select another input source, stop iPod playback to prevent your amp from selecting the iPod input source by mistake. •If any accessories are connected to your iPod, your amp may not be able to select the input source properly. •While your iPod is in the RI Dock, its volume control has no effect. If you adjust your iPod’s volume control while it’s in the RI Dock, make sure it’s not set too high before you reconnect your headphones. * If you use your iPod’s controls to start an iPod slideshow or video, these functions will not work, so use the remote controller instead. Using the RI Dock—Continued ¦ Using Your iPod’s Alarm Clock You can use your iPod’s Alarm Clock function to automatically turn on your iPod and amp at a specified time. Your amp’s input source will automatically be set to the input to which your iPod is connected. Notes: •This function only works when the OSD mode is set to Off. •To use this function, your iPod must be in the RI Dock, and the RI Dock must be con- nected to your amp with both an cable and an audio cable. •When you use this function, be sure to set your amp’s volume control to a suitable level. •Your amp may take several seconds to startup, so you might not hear the first few seconds of the first song/video. Notes: •To charge your iPod battery, the AC adapter must be plugged into a suitable wall outlet and connected to the RI Dock’s DC IN jack. •See your iPod’s instruction manual for more information on battery charging. ¦ Charging Your iPod’s Battery The RI Dock charges your iPod’s battery while your iPod is in the RI Dock. Setting the Remote Controller’s ID If you cannot adjust the volume of your Onkyo component with the DS-A3’s remote controller, try changing its remote control ID. The default setting is #1. Some Onkyo components are set to ID #2 or #3. •While pressing and holding down the [SETUP] button, press one of the following buttons for more than 3 seconds to set the ID: ID #1: PLAYLIST Up [ ] button ID #2: ALBUM Up [ ] button ID #3: PLAYLIST Down [ ] button ID #4: ALBUM Down [ ] button 15 Using the RI Dock—Continued Using Your Amp’s Remote Controller The following table shows which buttons on your amp’s remote controller you can use to control your iPod while it’s in the RI Dock. Be sure to select the appropriate remote mode first, and point your remote controller at your amp. Note that some buttons may be labelled differently, and some remote controllers may not have certain buttons. iPod function Remote controller button to use DescriptionTAPE mode HDD mode Turn on/off [STANDBY], [ON] — iPod is turned on and off. Play Play [ ] Starts playback on the iPod. If the iPod is not already on, it’s turned on automatically. Pause Pause [ ], Stop [ ] Pause [ ] Pauses iPod playback. Next song [ ], [ ] Next [ ] Selects the next iPod song. Previous song [ ], [ ] Previous [ ] Restarts the current iPod song. Press it twice to select the previous song. Fast forward — Fast Forward [ ] Press and hold to fast forward the iPod. Rewind — Rewind [ ] Press and hold to rewind the iPod. *To select the next or previous photo in an iPod photo slideshow, use the controls on your iPod photo. The following functions can be used with some Onkyo amps. iPod function Remote controller button to use DescriptionTAPE mode HDD mode Shuffle [DOLBY MODE] [RANDOM], [PLAYMODE], [SHUFFLE] Sets the iPod’s Shuffle function to: Songs, Albums, or Off. Repeat [REVERSE MODE] [REPEAT] Sets the iPod’s Repeat function to: One, All, or Off. Backlight REC [ ] [DISPLAY], [SCROLL] The iPod’s backlight comes on for 30 seconds. Next playlist — [PLAYLIST UP] Selects the next playlist on the iPod. Previous playlist — [PLAYLIST DOWN] Selects the previous playlist on the iPod. Next album — [ALBUM UP] Selects the next album on the iPod. Previous album — [ALBUM DOWN] Selects the previous album on the iPod. *Depending on your amp, some buttons may not work as expected. Troubleshooting ¦ There’s no sound •Make sure your iPod is actually playing. •Make sure your iPod is inserted properly in the RI Dock. •Make sure your amp is turned on, the...
Este manual também é adequado para os modelos :Speakers - D0901-2 (385.44 kb)