Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
For more wiring information regarding the Speakon connectors see page 17. ©American Audio® --PSW 15™/PSW 15P™ -Instruction Manual Page 6 Rear Panel: 2. INPUT LEVEL – This knob is used to regulate the output signal of the line level source con- nected to the Line Level Input Jacks (4 & 6). 3. FREQUENCY RESPONSE – This knob is used to adjust the crossover frequency of the sub- PSW 15™/PSW 15P™ Rear Panel Controls and Features Rear of PSW 15P™ 211109876543 Rear Panel: 2. INPUT LEVEL – This knob is used to regulate the output signal of the line level source con- nected to the Line Level Input Jacks (4 & 6). 3. FREQUENCY RESPONSE – This knob is used to adjust the crossover frequency of the sub- PSW 15™/PSW 15P™ Rear Panel Controls and Features Rear of PSW 15P™ 211109876543 4. BALANCED XLR/1/4” LINE INPUT – This connection is designed to accept a balanced line input signal from a mixer or other line level device with a balanced output jack. Use a balanced cable when the signal cable length exceeds 15 feet, this will reduce excessive signal loss. Be sure to connect only line level input devices such as mixers and tape machines to this jack. 5. XLR PARALLEL OUTPUT JACK – This jack is used to send the incoming signal from either of the Inputs Jacks to another PSW 15P™ or speaker. 6. BALANCED XLR/1/4” LINE INPUT – This connection is designed to accept a balanced line input signal from a mixer or other line level device with a balanced output jack. Use a balanced cable when the signal cable length exceeds 15 feet, this will reduce excessive signal loss. Be sure to connect only line level input devices such as mixers and tape machines to this jack. ©American Audio® --PSW 15™/PSW 15P™ -Instruction Manual Page 7 PSW 15™/PSW 15P™ Rear Panel Controls and Features PSW 15™/PSW 15P™ Rear Panel Controls and Features . XLR OUTPUT JACK – This jack is used to send the incoming signal from either of the Inputs Jacks to another PSW 15P™ or speaker. 8. VOLTAGE SELECTOR SWITCH -Because power supplies vary from location to location a voltage selector switch has been incorporated in the unit's design. This switch can select a voltage input of 120v or 230v to accommodate the two major power source. Always be sure to disconnect the power plug before changing the voltage. 9. MAIN POWER SWITCH – This is the main power ON/OFF button. Before main power is applied, be sure you have made all connections to the subwoofer. Remember to avoid damaging pops to the subwoofers, the mixer is turned on first and turned off last. 10. FUSE HOLDER – This housing stores the 6 amp GMA protective fuse. Always replace with the exact same type fuse, unless otherwise instructed, by an authorized American Audio® service technician. Replacing with any other type of fuse than that of the recommended fuse will void your unit warranty. 11. MAIN POWER INLET – This connector is used to supply main power to the unit via the included detachable power cord. The power connection uses an I.E.C. type connector, use only the supplied polarized AC power cord. Use only a power cord that matches this type of connection. Be sure to only connect this unit to a power outlet that matches the printed power label on the unit. Never use a power when the ground prong has been removed or broken off. The ground prong is used to reduce the risk of electrical shock in case of an electrical short. This cord is designed to fit in one direction only. Do not attempt to force a cord if it does not fit, be sure the cord is being inserted properly. ©American Audio® --PSW 15™/PSW 15P™ -Instruction Manual Page 8 AUX 4 AUX / IN MADE IN CHINA MODEL NO.: Q-3433 MKII POWER SOURCE: 115/230V~ 50/60Hz 20W MIN MAX TRIM OUTPUT ©American Audio® - - PSW 15™/PSW 15P™ - Instruction Manual Page 9 PSW 15™/PSW 15P™ Subwoofer Set-Up PSW 15P™ Input/Output Set-Up XLR-XLR Balanced Cables PSW 15P™ ©American Audio® - - PSW 15™/PSW 15P™ - Instruction Manual Page 10 Speakon Cables V4000 Amplifier XLR-XLR Balanced cables PSW 15™/PSW 15P™ Subwoofer Set-Up PSW 15™ Input/Output Set-Up AUX 4 AUX / IN MADE IN CHINA MODEL NO.: Q-3433 MKII POWER SOURCE: 115/230V~ 50/60Hz 20W MIN MAX TRIM OUTPUT OUTPUT INPUT PSW 15 Serial No. INPUT OUTPUT DLS 15 PSW 15™/PSW 15P™ Speakon Assembly PSW 15™/PSW 15P™ Speakon Assembly You will need a pair of Neutrik Speakon® NL4FC connectors. You will also need high-quality two or four conductor subwoofer cable, a pair of needle-nosed pliers and a 1.5mm Allen key to assemble the Speakon connectors to your subwoofer wire. To assemble the Neutrik Speakon NL4FC connector, complete the following steps: Figure 10 1. Strip back 3 /4-inch of the cable casing. Strip off 1 /4-inch from the end of each of the conductors down to bare wire, and insert the brass fittings ( Figure 10). 2. Slide the cable tension clip (D) and the speakon Brass Inserts 4-Conductor Speaker Cable coupler (E) through the cable end. See...