Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
• The brightness of the display can be adjusted: High . Low . Off . High . SETTING THE CLOCK AND DATE 1. In any mode, press and hold TIME SET until clock digits flashes. 2. Press 2; to select 12 Hours/ 24 Hours mode. 3. Hold down or press .1 / 2™ repeatedly to set and adjust the hours. 4. Press TIME SET to confirm. ™ The clock digits for the minutes flash. 5. Repeat the steps 3 - 4 until you complete all the other settings for minutes, year, month and days. TUNER 1 Press TUNER/AUX once to switch on the radio (FM only). ™Display shows the radio frequency of the last selected waveband. Your pre set station is also shown if you are listening to a preset. (See 2) 2 Adjust the sound using VOL+/-. 3 To select preset stations, press the respective PRESET button (1-5). TUNING TO RADIO STATIONS 1 Press and hold .1 / 2™ until the frequency in the display starts changing. ™Display shows “Scrh” during automatic tuning. ™After the system tunes to a station of sufficient reception, display shows its frequency. • To tune to a weak station, press .1 / 2™ briefly and repeatedly until an optimal reception is found. To improve reception (FM): Extend and position the pigtail fully to obtain optimum reception. STORING AND USING PRESET STATIONS You can store up to 5 FM radio stations in the memory. 1 Tune to your desired station (see TUNING TO RADIO STATIONS). 2 To store a preset, hold down briefly on a PRESET button 1-5 until you hear a dou ble beep. ™ Display shows the preset number of your station. 3 Repeat steps 1 and 2 to store your other stations. • You can overwrite a preset station by storing another frequency in its place. 4 Press a PRESET button 1-5 (or PRESET 4/ 3on the remote control) to listen to a preset station. ™ To display clock time, press 2; on the set. USING THE ALARM GENERAL Two different alarm times can be set. This can be useful when you need to be woken up at a different time e.g. during the week and at the weekend, and you can set different wake-up modes: • tuner mode. • buzzer mode. The gentle wake buzzer alarm increases its beep tone frequency within seconds. • dock mode SETTING THE ALARM TIME (See 3) 1 In any mode, press and hold ALM1 or ALM2 for two seconds. ™ ALM1 / ALM2 icon and the hour digits flash. And the icon for the current alarm mode also flashes. 2 Hold down or press .1 / 2™ repeatedly to set and adjust the hours. 3 Press ALM1 or ALM2 to confirm. ™ ALM1 / ALM2 icon and the minutes digits flash. And the icon for the current alarm mode also flashes. 4 Hold down or press .1 / 2™ repeatedly to set and adjust the mintues. 5 Press ALM1 or ALM2 to confirm. SETTING THE ALARM MODE 1 Press POWER to switch to standby mode. 2 Select your choice of alarm mode: either docked player, buzzer, or radio by using the DOCK•BUZZER •TUNER slider. • At the set alarm time, the docked player or radio or buzzer will switch on automatically. Helpful hints: – If you have selected TUNER alarm mode, make sure you have properly tuned to a station before turning off the set. – If you have selected DOCK alarm mode, make sure you have docked the compatible player, or the buzzer mode will be selected automatically. – To check the alarm time setting for ALM1 or ALM2, press ALM1 or ALM2. SWITCHING OFF THE ALARM There are three ways of switching off the alarm. Unless you cancel the alarm completely, the 24-hour ALARM RESET will be automatically selected after 59 minutes from the time your alarm first goes off. 24 HOUR ALARM RESET If you want the alarm mode to be stopped immediately but also wish to retain the same alarm setting for the following day: • Press POWER. REPEAT ALARM This repeats your alarm call at 9 minute intervals. • During the alarm call, press REPEAT ALARM / BRIGHTNESS CONTROL.. ™ Display shows ALM1 or ALM2 flashing during a repeat alarm. • Repeat if desired (up to a maximum of 6 times). CANCELING THE ALARM COMPLETELY • Press ALM 1 or ALM 2 button once or more until ALM1 or ALM2 disappears. DOCK (See 4) By connecting the iPod to your AJ301DB, you can listen to the sound of the docked player through the powerful speakers of the Hi-Fi system. COMPATIBLE PORTABLE PLAYER • Apple iPod models with 30-pin dock connector as follows: Nano 1st /2nd/3rd generation, iPod 5th generation (video), iPod touch and iPod classic. DOCK ADAPTERS Before plugging your player in the dock, snap the suitable dock adaptor into the dock to provide a snug fit for the player to be docked. Selecting the correct dock adaptor • 4 iPod dock adaptors are included. Each adaptor has indication to match different iPod types. PLAYING APPLE iPod USING AJ301DB 1 Snap the compatible iPod into the dock connector. 2 Press DOCK to switch on the dock mode. 3 The connected player will play automatically. Notes: – In dock mode, if no player is docked for 15 minutes, AJ301DB will come to standby. – By using the buttons ( 2;, .1, 2™ and VOLUME ) on the AJ301DB and its remote control, the following iPod playback features are available: Play/Pause, selecting next...