Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
This work must be done only by a qualified electrician, using copper wire only. WARNING: USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS NOT RECOMMENDED. IMPROPER CONNECTION MAY CREATE THE RISK OF ELECTROCUTION. USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA. 3. Where possible, avoid the use of extension cords. If they must be used, minimize the risk of overheating by ensuring that they are UL listed and of the proper gauge and length. Never use a single extension cord to operate more than one fan. 4. Do not insert fingers or foreign objects into the fan. Do not block or tamper with the fan in any manner while it is in operation. Do not touch the fan while in operation or just after it has been turned off, as some parts may be hot enough to cause injury. 5. Unplug power cord before installing or servicing the fan. WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR SERVICING THE FAN. ALWAYS UNPLUG THE POWER CORD. DESCRIPTION 6. This fan is intended for general use ONLY. It must NOT be used in The AirKing 9" (22.9 cm) oscillating fan features whisper-quiet perfor-potentially dangerous locations such as flammable, explosive, chemimance with a 3-paddle fan blade. The fan has a permanently lubricated cal-laden or wet atmospheres. motor with a 6 ft (1.8 m) 18/3 cord set. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL SPECIFICATIONS DEVICE. Motor ................................................ 120V, 60 Hz 7. Be sure fan is on a stable surface when operating, to avoid chance of it Blade diameter ................................ 9" (22.9 cm) overturning. Speeds ............................................. 2 8. DO NOT use fan in a window. Rain may create an electrical hazard. Control ............................................. Rotary Switch Air flow distribution .......................... 90° 9. Completely reassemble fan, according to instructions before reconnect- Approvals ......................................... UL Listed. Close mesh fan ing to power supply. guard meets OSHA requirements. MAINTENANCE MODEL 4C523K/9154K SPEED HIGH LOW CFM 1205 906 M3/s .57 .43 RPM 2175 1644 Amps .55 .32 Watts 32 22 dB A 41 34 WARNING: ALWAYS UNPLUG THE CORD BEFORE SERVICING. CLEANING: Use a soft cloth and a mild soap solution such as liquid dish washing detergent. CAUTION: Do not use gasoline, benzine, thinner, harsh cleaners, etc. which will damage the fan. Dry all parts with a soft cloth completely before reconnecting to power supply. STORAGE: When not in use, keep unit in a clean dry place. MOTOR IS PERMANENTLY LUBRICATED. 2084020A Rev. F 9/00 1 MANUAL DE INSTRUCCIONES DE OPERACION Y PARTESMODEL 4C523K/9154K MANUAL DE INSTRUCCIONES DE OPERACION Y PARTESMODEL 4C523K/9154K HUB R 9" (22.9 cm) VENTILADOR 4. Place HOOK on FRONT GRILL over top center wire on REAR GRILL. ASSEMBLY Align GRILLS. MULTIDIRECCIONAL (Assembly Illustration - Page 1) 5. With a twist, gently remove GRILL CLIPS from HOLDER and position MODELO 4C523K/9154K 1. Place REAR GRILL on MOTOR. Align holes in REAR GRILL with pins evenly around fan. Attach clips by snapping tail of CLIP over round wire on MOTOR. on REAR GRILL. Snap body of CLIP around flat wires of both GRILLS. 2. Fasten REAR GRILL with PLASTIC NUT. (Figures a and b, Page 1) LEA Y GUARDE ESTAS INSTRUCCIONES LEALAS CUIDADOSAMENTE ANTES DE INTENTAR ARMAR, INSTALAR, OPERAR O DAR MANTENIMIENTO AL PRODUCTO 3. To avoid damaging BLADE, install by pushing firmly in CENTER HUB, onto MOTOR SHAFT. (Follow steps below) OPERATION DESCRITO. PROTEJASE A SI MISMO Y A LOS DEMAS OBSERVANDO TODA LA INFORMACION SOBRE SEGURIDAD. .NO a UP b TAP HUB c SPIN 1. SPEEDS: The speed is controlled by the rotary switch located on the SEGUIR LAS INSTRUCCIONES PODRIA RESULTAR EN LESIONES PERSONALES Y/O DANOS A LA PROPIEDAD! a) Pull oscillating knob up to fan stand. GUARDE LAS INSTRUCCIONES PARA REFERENCIAS FUTURAS. disengage oscillating 2. OSCILLATION: Push down on the knob on the motor cover to start fan Center mechanism. oscillation. Pull up on the knob to stop fan oscillation. b) Using a blunt object, such INFORMACION GENERAL SOBRE SEGURIDAD as a screwdriver handle, 3. ANGLE ADJUSTMENT: The angle of the upper fan assembly may be 11 22 27 DESCRIPCION El ventilador oscilante AirKing de 9" (22.9 cm) es de operacion silenciosa y tiene una unidad giratoria de 3 paletas. El ventilador tiene un motor permanentemente lubricado con un cordon electrico de 6 pies (1.8 m) 18/3....
Este manual também é adequado para os modelos :Speakers - 4C523K (122.23 kb)