Log:
Assessments - 3, GPA: 4 ( )

Instruções de Operação JBL, Modelo 1950-0113-001

Fabricante : JBL
Arquivo Tamanho: 431.97 kb
Arquivo Nome :
Língua de Ensino: itenesfrde
Ir para baixar



Facilidade de uso


Is the LED On? If the LED is not on, power is not getting to your JBL Radial. Try the solutions shown. Incorrect source selection Ensure that the iPod is properly docked or that the auxillary cable is properly connected to an external audio device. Turn up the volume. Check the system with a known good source. Connect the aux-in cable to the headphone jack on your iPod. Sound only comes from one side / channel. iPod or audio cable is not seated properly. Make sure the iPod or Aux in cable is seated all the way into the JBL Radial. If you are using an extension cable or a third party cable, make sure it is a stereo 3.5mm male to male cable. Distortion (static, crackling or hissing sound) Noise may be caused by interference from a monitor, cell phone or other transmitting device. Turn monitor off to see if noise is eliminated. Move JBL Radial cables farther away from monitor. 950-0113-001 7 JBL® Radial Manual SYMPTOM POSSIBLE PROBLEM SOLUTION NOTE SOUND QUALITY Too much bass or treble JBL Radial is being overdriven by an amplified audio source. Ensure that the JBL Radial is connected to an appropriate source device. Make sure that all signal cables are inserted snugly into receptacles. Volume level may be too high Check volume of source device. Some devices will distort the output signal if the volume is set to maximum. Check the EQ setting on your iPod or source device. JBL Recommends that the source device EQ be set to flat or OFF JBL Radial emits a loud hum or buzzing noise. Input cables not plugged in properly. Check input cable connection. Speaker system experiences radio frequency interference or picks up a radio station. Input cable may be picking up interference. Wrap up excess input cable in order to make as short as possible. 950-0113-001 8 JBL® Radial Manual SYMPTOM POSSIBLE PROBLEM SOLUTION NOTE CHARGING SYNCING iPod will not charge Wrong adaptor is used. Ensure correct adaptor is used for your specifi c iPod model. The iPod is not making full Ensure iPod is seated contact with the dock station. securely into the docking station. iPod is not recognized by the Third party accessories may Make sure you do not have computer when docked into be conflicting with the USB or the JBL Radial connected to a the JBL Radial or there is an fi rwire signal. USB or fi rewire hub. error in data transfer. Connect the JBL Radial directly into the computers USB or fi rewire port. USB or firewire port is not Try connecting the USB or supplying enough power firewire cable to another port on the back of the computer. SPECIFICATIONS Manufacturer Harman Multimedia Model JBL Radial Driver (Full Range) Hercules 45mm Drivers (Tweeter) Odyssey 25mm Power 1 x 30 watts (woofer), 2 x 15 watts (tweeters), at 1% THD Dimensions Width: 12.0 inches 305mm Depth: 5.25 inches 135mm Height: 10.5 inches 270mm Input Impedance >10k Ohm Signal-to-Noise ratio >85dB Frequency Response 70 – 20 kHz Input Sensitivity 250 mV rms for rated power output USA/Canada Power 120 volts, 60Hz A...

Este manual também é adequado para os modelos :
Speakers - 10950-0113-001 (431.97 kb)
Speakers - 4950-0113-001 (431.97 kb)
Speakers - 5950-0113-001 (431.97 kb)
Speakers - 6950-0113-001 (431.97 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias