Assessments - 2, GPA: 5
(
)
)
|
Fotos e especificações Yamaha NS-F150 |
Facilidade de uso
• To avoid accidents resulting from tripping over loose speaker cables, affix them to the floor. • Placing this unit too close to a CRT TV set might impair picture color or create a buzzing noise. In this case, move the speakers away from the TV. This is not an issue with LCD and plasma TVs. • Only for NS-F140, you can install commercially available legs or spikes onto the speaker to increase its stability and improve the sound quality. Screw holes on the bottom of the speaker; Diameter: 8 mm (1/3") Hole depth: 18 mm (2/3") For more information about how to install legs or spikes, refer to the instruction manual that comes with it. English 1 En Placing the speakers Placing the speakers ¦ Using as 2ch stereo speakers Better stereo images will be obtained when the speakers are slightly angled in towards the listener. ¦ Using as front speakers in a multi-channel system Position the speakers on both sides of the TV. The NS-F150/ NS-F150/ positioning of speakers is important, since this NS-F140 NS-F140 dictates the overall sound quality of the multi-channel system. Set up the speakers on the basis of your Center listening position by following the owner’s manual supplied with your amplifier. Surround Surround ¦ Removing / Attaching the grille To remove the grille, gently pull the grille away from the speaker. To attach the grille, line up the holes on the grille with the pegs on the speaker, and gently push the grille onto the speaker. (Grille rear view) NS-F150 only Top Bottom Notes • When removing or attaching the grille, be careful not to touch the drive units, and not to exert excessive force with any tools. • Do not touch or apply impact to the speaker’s diaphragm. Otherwise, the speaker may malfunction. • To avoid damaging the grille, never apply excessive force, and be sure to use its frame, never pull or push the surface, for removing or attaching the grille. 2 En Connecting to your amplifier EnglishBefore making connections, make sure that the amplifier is switched off. Connecting to your amplifier Note Do not insert the insulation into the terminal. If the connections are faulty, you will hear no sound from the speaker. Loosen Tighten Amplifier or Receiver NS-F150/NS-F140 Positive (+) Negative (–) NS-F150/NS-F140 Left Right 15 mm (5/8") Speakers output terminals ¦ How to connect the speaker cables 1 Remove 15 mm (5/8") of insulation from each end of the cables, and twist the exposed conductors together neatly and tightly, as shown left. 2 Loosen the terminal knob. 3 Insert the bare wire. Good No Good 4 Tighten the knob and secure the cable. 5 Test the firmness of the connection by pulling lightly on the cable at the terminal. Notes • Make sure the terminal is gripping the bare wire, not the insulation. • Make sure the bare wires do not touch each other, as this could damage the speaker or amplifier. • If the connections are faulty, you will hear no sound from the speakers. ¦ Connecting to an amplifier or a receiver Connect one speaker to the left (marked L) terminals of your amplifier or receiver, and another speaker to the right (marked R) terminals. Please refer to the owner’s manual that came with your amplifier or receiver. Notes • Make sure you connect the speakers with the correct polarity—positive (+) terminals to positive (+) terminals, and negative (–) terminals to negative (–) terminals. If you get them crossed over, the sound will be unnatural and lack bass. • The speaker may be damaged if certain sounds are continuously output at high volume level. For example, if sine waves from a test disc, bass sounds from electronic instruments, etc., are continuously output, or when the stylus of a turntable touches the surface of a disc, reduce the volume level to prevent the speaker from being damaged. • Once you have connected all of the speakers, plug the amplifier and other AV components into suitable AC wall outlets. • When using an amplifier with a rated output power higher than the nominal input power of the speaker, care should be taken never to exceed the speaker’s maximum input. 3 En Specifications ¦ When using a banana plug 1 Tighten the terminal knob. 2 Simply insert the banana plug into the terminal. Banana plug Specifications ¦ NS-F150 Type..................................... 2-way Bass Reflex speaker system Non-magnetic shielding type Driver ........................... Woofer: 16 cm (6-1/2") cone type x 2 Tweeter: 3 cm (1") soft dome type Nominal input power ....................................................... 50 W Maximum input power .................................................. 180 W Impedance .............................................................Nominal 6 . Frequency response .......................... 37 Hz–30 kHz (–10 dB) Sensitivity ......................................................88 dB/2.83 V, 1 m Dimensions (W x H x D) ...................200 x 1030 x 362 mm (7-7/8" x 40-1/2" x 14-1/4") Weight .............................................................11.2 ...
Este manual também é adequado para os modelos :Speakers - NS-F140 (2.13 mb)