Assessments - 1, GPA: 3
(
)
)
|
Fotos e especificações Yamaha Soavo-900SW |
Facilidade de uso
. Optimum bass sounds with various settings Setting high cut and phase keeps the optimum sound quality balance between the front speakers and this unit. . B.A.S.S. mode button This unit is equipped with the B.A.S.S. mode button so that you can enjoy bass sound that matches any kind of source. • In this manual, operations that can be performed using either the front panel of this unit or the remote control are explained using the remote control. • y indicates a tip for your operation. • Notes contain important information about safety and operating instructions. Supplied accessories Check that you have received all of the following parts. Power cable Batteries (2) (AA, R6, UM-3) POWER STANDBY SLEEP PHASE MEMORY PRESET HIGH CUT VOLUME 21 3 B.A.S.S. Remote control 2 En GETTING STARTED GETTING STARTED ¦Front panel English H-CUT SUBWOOFER SYSTEM Soavo-900SW STANDBY /ON STANDBY /ON PHASE 1 2 3 1 2 3 B.A.S.S. PRESET 140Hz40Hz VOLUME 100 12345678 1 Remote control sensor Receives signals from the remote control. 2 STANDBY/ON indicator Green: Lights up when this unit is on. Red: Lights up when this unit is in the standby mode. Orange: Lights up when the sleep timer is on. 3 PHASE indicator Green: Lights up when the phase is set in the reverse mode. Red: Lights up when the phase is set in the regular mode. 4 STANDBY/ON switch Turns on or sets this unit to the standby mode. Note In the standby mode, this unit consumes a small amount of power. 5 H-CUT control Adjusts the high frequency cut off point depending on the connected front speakers or your preference (see page 13). One graduation of this control represents 10 Hz. H-CUT 6 VOLUME control Adjusts the volume level. Turn the control clockwise to increase the volume, counterclockwise to decrease the volume. 7 B.A.S.S. indicators Light up to indicate the currently selected B.A.S.S. number (1, 2 or 3) (see page 13). 8 PRESET indicators Light up to indicate the currently selected PRESET number (1, 2 or 3) (see page 14). Notes • If you set this unit to the standby mode when one of the PRESET indicators is lit, no PRESET indicator lights up when you turn on this unit next time. • The PRESET indicator turns off when you press any button other than PRESET 1, 2, or 3, or when you operate any other function of this unit. 3 En GETTING STARTED GETTING STARTED Rear panel OUTPUT TO SPEAKERS FROM AMPLIFIER INPUT 3 INPUT 2 INPUT 1 LLL R RR LR MONO POWER ON OFF 1 GND terminal See page 12 for connection information. 2 INPUT 3 terminals See pages 7 - 8 for connection information. 3 INPUT 2 (LFE) terminals See page 8 for connection information. 4 OUTPUT terminals See page 10 for connection information. ¦Remote control POWER STANDBY SLEEP PHASE MEMORY PRESET HIGH CUT VOLUME 21 3 B.A.S.S. 123459876 1 STANDBY Sets this unit to the standby mode. Note In the standby mode, this unit consumes a small amount of power. 2 POWER Turns on this unit. 5 INPUT 1 terminals See pages 10 - 11 for connection information. 6 AC IN Connects the supplied power cable (see page 12). 7 POWER switch Switches the power (ON/OFF) of this unit. Normally, set this switch to the ON position. When this unit is not used for a long period of time, set the switch to the OFF position. 3 B.A.S.S. Selects a mode that is suitable for the source. Each time you press B.A.S.S., the B.A.S.S. indicator changes between 1, 2, and 3. 4 PRESET Stores or recalls the B.A.S.S., volume, high-cut frequency and phase settings (see page 14). 5 HIGH CUT / Adjusts the high frequency cut off point depending on the connected front speakers or your preference (see page 13). 6 SLEEP Sets the sleep timer (see page 14). 7 PHASE Switches the phase mode. Normally, set this unit to the reverse position. However, according to your speaker systems or the listening condition, there may be cases when better sound quality is obtained by setting this switch to the normal position. Select the better position by monitoring the sound. 8 MEMORY Stores the B.A.S.S., volume, high-cut frequency and phase settings (see page 14). 9 VOLUME / Adjusts the volume of this unit. 4 En GETTING STARTED GETTING STARTED ¦Installing the batteries in the remote ¦Using the remote control control English 3 1 2 1 Press the mark on the battery cover and open the cover. 2 Insert the two supplied type AA, R6, UM-3 batteries following the indications (+/–) inside the battery compartment. 3 Close the battery cover. Replacing the batteries Change all of the batteries if you notice conditions such as the operation range of the remote control decreases. Notes • Do not use an old battery together with a new one. • Do not use different types of batteries (for example, alkaline and manganese) together. Each type of battery has its own characteristics even if they are similar in shape. • If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak. • Dispose of the batteries according to the regional regulations. • If a battery starts leaking, d...