Assessments - 8, GPA: 3.8
(
)
)
|
Fotos e especificações Yamaha YST-RSW300 |
Facilidade de uso
¦ Using one subwoofer (with speaker cables) Right speaker Subwoofer Left speaker OUTPUT TO SPEAKERS INPUT 2 /MONO LOW AUTO STANDBY INPUT 1 FROM AMPLIFIER POWER ON OFF OFF HIGH NORM REV PHASE OUTPUT TO SPEAKERS /MONO INPUT 2 FROM AMPLIFIER INPUT 1 R L L LR R Amplifier Speaker output terminals ¦ Using two subwoofers (with speaker cables) Speaker output Right speaker Left speaker OUTPUT TO SPEAKERS INPUT 2 /MONO LOW AUTO STANDBY INPUT 1 FROM AMPLIFIER POWER ON OFF OFF HIGH NORM REV PHASE OUTPUT TO SPEAKERS INPUT 2 /MONO LOW AUTO STANDBY INPUT 1 FROM AMPLIFIER POWER ON OFF OFF HIGH NORM REV PHASE OUTPUT TO SPEAKERS /MONO INPUT 2 INPUT 1 FROM AMPLIFIER FROM AMPLIFIER INPUT 1 R L L LR R RLR Amplifier Subwoofer Subwoofer terminals 8 En CONNECTIONS CONNECTIONS Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT terminals of the subwoofer to the main speakers. ¦ Using one subwoofer (with speaker cables) English Right speaker Left speaker OUTPUT TO SPEAKERS INPUT 2 /MONO LOW AUTO STANDBY INPUT 1 FROM AMPLIFIER POWER ON OFF OFF HIGH NORM REV PHASE OUTPUT TO SPEAKERS /MONO INPUT 2 FROM AMPLIFIER INPUT 1 R L L LR R Subwoofer Amplifier Speaker output terminals ¦ Using two subwoofers (with speaker cables) Right speaker Left speaker OUTPUT TO SPEAKERS INPUT 2 /MONO LOW AUTO STANDBY INPUT 1 FROM AMPLIFIER POWER ON OFF OFF HIGH NORM REV PHASE OUTPUT TO SPEAKERS INPUT 2 /MONO LOW AUTO STANDBY INPUT 1 FROM AMPLIFIER POWER ON OFF OFF HIGH NORM REV PHASE OUTPUT TO SPEAKERS /MONO INPUT 2 FROM AMPLIFIER INPUT 1 OUTPUT TO SPEAKERS /MONO INPUT 2 FROM AMPLIFIER INPUT 1 R L L LR R R L L LR R Subwoofer Speaker output terminals Amplifier Subwoofer 9 En CONNECTIONS CONNECTIONS For connection, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the connections are faulty, no sound will be heard from the subwoofer or the speakers, or both of them. Make sure that the + and – polarity markings of the speaker cables are observed and set correctly. If these cables are reversed, the sound will be unnatural and lack bass. Caution Do not let the bare speaker wires touch each other, because this could damage the subwoofer or the amplifier, or both of them. ¦ Before connecting Remove the insulation coating at the extremity of each speaker cable by twisting the coating off. Good No Good 10mm (3/8”) ¦ How to connect 1 Press and hold the terminal’s tab, as shown in the figure below. 2 Insert the bare wire. 3 Release your finger from the tab to allow it to lock securely on the cable’s wire end. 4 Test the firmness of the connection by pulling lightly on the cable at the terminal. 21Black: negative (–) Red: positive (+) Note Do not insert the insulation coating into the hole. The sound may not be produced. 10 En CONNECTIONS CONNECTIONS After all connections are completed, plug in the subwoofer and other audio/video components to the AC outlet. OUTPUT TO SPEAKERS INPUT 2 /MONO LOW AUTO STANDBY INPUT 1 FROM AMPLIFIER POWER ON OFF OFF HIGH NORM REV PHASE (U.S.A. model) To AC outlet ¦ VOLTAGE SELECTOR switch (For Asia and General models only) This unit has a voltage selector switch on the rear panel. If the preset setting of the switch is incorrect, set the switch to the proper voltage range (110/120/ 220/230-240 V) of your area. Consult your dealer if you are unsure of the correct setting. VOLTAGE SELECTOR WARNING Do not plug the subwoofer to the AC outlet before setting the VOLTAGE SELECTOR. English 11 En ADJUSTING THE SUBWOOFER BEFORE USE ADJUSTING THE SUBWOOFER BEFORE USE Subwoofer rear panel OUTPUT TO SPEAKERS INPUT 2 /MONO LOW AUTO STANDBY INPUT 1 FROM AMPLIFIER POWER ON OFF OFF HIGH NORM REV PHASE NORM REV PHASE 3 7 (U.S.A. model) 40Hz 140Hz 0 10 STANDBY/ON HIGH CUT VOLUME SUBWOOFER SYSTEM YST-RSW300 3 5,6 1,6 1 Set the VOLUME control to minimum (0). 2 Turn on the power of all the other components. 3 Make sure that the POWER switch on the rear panel is set to the ON position, then press the STANDBY/ON switch on the front panel to turn on the subwoofer. * The status indicator lights up in green. 4 Play a source containing low-frequency signals and adjust the amplifier’s volume control to the desired listening level. 5 Adjust the HIGH CUT control to the position where the desired response can be obtained. Normally, set the control to the level a little higher than the main speaker’s rated minimum reproducible frequency*. * The main speaker’s rated minimum reproducible frequency can be looked up in the speakers’ catalog or owner’s manual. 6 Increase the volume gradually to adjust the volume balance between the subwoofer and the main speakers. Normally, set the control to the level where you can obtain a little more bass effect than when the subwoofer is not used. If the desired response cannot be obtained, adjust the HIGH CUT control and the VOLUME control again. Subwoofer front panel 7 Set the PHASE switch to the position which gives ...