Assessments - 3, GPA: 4.3
(
)
)
|
Fotos e especificações Yamaha NS-125F |
por este dispositivo também tem outras instruções :
Facilidade de uso
• When & is pressed on the recording component, recording stops and recording standby mode is cleared. Playback continues on the CD player. SYSTEM CONTROL Copy time control By specifying the length of the tape, CRX-E300 programs tracks or helps you to program tracks so they will fit onto the tape with the least amount of unrecorded space remaining at each end of the tape. 1 Manual tape programming REP POWER 1 2 3 1 2 3 4 5 6 4 5 6 7 8 9 7 8 0 +10 +100 REP RANDOM PROG A B C TEXT/TIME R. TIME D E TAPE DIRECTION PRESET TUNER PRESET MD CD TAPE AUX MD REC/PAUSE TAPE REC/PAUSE MODE DUBBING START SLEEP DISPLAY VOLUME FREQ/RDS MODE–PTY SEEK–START PROG R.TIME CD DUBBING DUBBING MODE START 1 Insert the desired disc into the CD player, and load a blank tape into the KX-E300. 2 Press CD. 3 Press R.TIME repeatedly to select the length of tape to be used. Each time you press R.TIME, the length of the tape changes as follows: 46 54 90 60 • You can use numeric buttons to input the length of the tape. 4 Press PROG to start programming. •“A B”appears in the display to indicate the direction of the tape. 5 Select the desired track number using numeric buttons. • Repeat step 5 to continue programming tracks. • The remaining time is shown on the display. If the track is longer than the remaining time, “TM Over”appears on the display. 6 Press R.TIME to continue programming tracks on side B. • Repeat step 5. 7 Choose CD = TAPE by pressing DUBBING MODE, and press DUBBING START to start recording. 2 Automatic tape programming 1 Repeat steps 1 to 3 of “Manual tape programming”. 2 Press REP to start programming. • Programming is done in the order on the CD from side A to side B. When complete, the following display appears. (Example) when 11 tracks have been programmed PROG B You can change the program data following the steps described on page 18, “To change program data”. 3 Choose CD = TAPE by pressing DUBBING MODE, and press DUBBING START to start recording. To stop dubbing Press & on KX-E300. To cancel tape programming Press & on CRX-E300 when dubbing is stopped. English ADDITIONAL INFORMATION ADDITIONAL INFORMATION If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. When taking the service, the MDX-E300 or KX-E300 may be needed. For details, contact your authorized YAMAHA dealer or service center. SYMPTOM CAUSE REMEDY RECEIVER The unit does not switch ON when the STANDBY/ON switch is pressed. The AC power cord is not connected or not completely connected. Securely connect the power cord. No sound from one speaker. Loose speaker connections. Connect properly. The sound suddenly goes off. The protection circuit has been activated because of a short circuit, etc. Check that the speaker wires are not touching each other and then turn the unit back on. No sound from an external unit connected with this unit or play does not begin. Incorrect cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Input source selection is not proper. Make a proper input source selection. Sound distorted. The component connected to this unit is disconnected from AC outlet. Connect the AC power cord of the component to an AC outlet. Excessive static in FM broadcasts. Interference from starting motor of a nearby car. Position the FM antenna as high and as far away from nearby roads as possible. Connect using a coaxial cable. Interference from the thermostat of a nearby electrical appliance. Noise increases during stereo broadcasts. Antenna input is too weak due to obstructions or excessive distance from the broadcasting station. Check the antenna connection. Install a multi-element type FM antenna if possible. Stereo broadcasts are noisy and STEREO indicator blinks on and off. Insufficient antenna input. Install an antenna appropriate for the electric field strength of your area. Cannot select preset stations. Preset memory has been erased. Reprogram memory presets. Buzzing or static during AM broadcasts. Interference from sources such as lightning, fluorescent lights, electric motors or thermostat of nearby electrical appliance. The problem is difficult to eliminate, but can be lessened by grounding AM loop antenna. TV or microprocessor is being used nearby. Move away from TV or microprocessor. AM broadcast sensitivity is poor. Radio signal is weak or the antenna is not properly connected. Properly connect the AM loop antenna. Change orientation of the AM loop antenna. Install an external AM loop antenna. Cannot set timer. Current time is not set. Set current time. The unit does not work normally. The internal microcomputer has been frozen by an external electric shock (lightning, excessive static electricity, etc.) or the power supply with low...