Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Better surround effect will result if all speakers are set at the same distance from the listening position. Place the front speakers at a suitable distance to the left and right of the television. Place the subwoofer on either side of the television. Place the center speaker on the top-center of the TV set. The placement of rear speakers greatly depends on the configuration of the room. The rear speakers may be placed on both sides of the listening position A or behind the listening position B. Tips • Movies are best enjoyed in a room that produces no echoes (as in one with surrounding curtains). • Music (especially classical music) is best enjoyed in a room that produces some echo. Setting the speakers To prevent speaker vibration or movement while listening, attach the supplied foot pads to the bottom four corners of the center speaker*, front speakers, and rear speakers*(F). *SA-VE325 only Setting the center speaker (SA-VE325 only) (G) Set the center speaker firmly on top of the TV set, making sure it is completely level. Setting other speakers(H) For greater flexibility in the positioning of the speakers, use the optional WS-FV10A, WS-TV10A, or WS-WV10A speaker stand (available only in certain countries). Tip The height of the front speakers should be adjusted to about the center of the TV screen (I). Listening to the sound (J) First, turn down the volume on the amplifier. The volume should be set to minimum before you begin playing the program source. 1 Turn on the amplifier and select the program source. 2 Press POWER on the subwoofer. The ON/STANDBY indicator on the subwoofer lights up green. 3 Play the program source. Power turns on and off automatically — Auto power on/off function (K) When the subwoofer is on (i.e, the ON/STANDBY indicator lights up green) and there is no signal input for a few minutes, the ON/STANDBY indicator changes to red and the subwoofer enters power saving mode. While in this mode a signal is input to the subwoofer, the subwoofer automatically turns on (auto power on/off function). To turn this feature off, slide the POWER SAVE switch on the rear panel to OFF. Note If you turn down the volume level of the amplifier too low, the auto power on/off function may activate, causing the subwoofer to enter power saving mode. Adjusting the sound Slight adjustments to the system can enhance your sound enjoyment. Adjusting the subwoofer (J) 1 Set MODE according to the program source as follows: Source MODE DVD, LD, video cassette MOVIE or other video source MD, CD, cassette tape MUSIC or other audio source 2 Rotate LEVEL to adjust the volume. Set the volume level to best suit your preference according to the program source. Notes • Some amplifier functions for enhancing the sound may cause distortion in the subwoofer. If such distortion occurs, turn off those functions. • To enjoy high-quality sound, do not turn the subwoofer volume too high. • To increase the bass sound from the subwoofer, connect the system using “Hookup B”. • The bass sound is enhanced in MOVIE mode rather than in MUSIC mode. Therefore, if you change the mode to MOVIE while listening to some sources that do not include the bass sound, you may not be able to get the effect. Setting amplifier to enjoy movies (SA-VE325 only) For the Dolby Digital (AC-3) If your amplifier is connected internally or externally with a Dolby Digital (AC-3) processor, you should use the setup menus for the amplifier to specify the parameters of your speaker system. See the table below for the proper settings. For details on the setting procedure, refer to the manual that was provided with your amplifier. Select Micro Satellite Position if a Sony amplifier provides it. When “Hookup A” is used (Speaker setup) For Set to Front speakers SMALL Center speaker SMALL Rear speakers SMALL Subwoofer ON (or YES) When “Hookup B” is used (Speaker setup) For Set to Front speakers LARGE Center speaker SMALL Rear speakers SMALL Subwoofer OFF (or NO) For the Dolby Pro Logic If your amplifier is connected internally or externally with a Dolby Pro Logic processor, you should set the surround effect mode to “NORMAL” on the amplifier for your particular speaker system. For details on the setting procedure, refer to the manual that was provided with your amplifier. Troubleshooting Should you encounter a problem with your speaker system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sony dealer. There is no sound from the speaker system. •Make sure all the connections have been correctly made. •Make sure the volume on the amplifier has been turned up properly. •Make sure the program source selector on the amplifier is set to the proper source. •Check if headphones are connected. If they are, disconnect them. There is distortion in the subwoofer sound output. •Check if any sound-enhancing functions have been activated on the amplifier. If they have, turn them off. There is hum or noise in the speaker outpu...