Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
• After installing, make sure the speakers are securely fixed. 50 cm (19 11/16 in.) from the side wall 20 cm (7 7/8 in.) from the back wall 50. to 60. Use M5 screws. The screw hole depth: 9 mm (3/8 in.) 60 mm (2 3/8 in.) Grille Speaker’s rear view Safety support fixture Screw Strong cords Speaker’s rear view Safety support fixture Grille Screw Strong cords Strong cords 4 En • Pioneer is not responsible for any accidents or damage that result from improper installation, misuse or modification of the product, or natural disasters. Applying non skid pads The use of non skid pads is recommended depending on the installation location. Apply the pads to the four corners of the side of the speaker which will be on the bottom. Note that depending on the location, the pads may not provide fully sufficient traction to prevent slipping, so care should be taken not to install the speakers in conditions where they may be prone to side. • When applying non skid pads, laid down the speaker on the soft cloth etc. to avoid working with unstable position. Attaching and removing the grille The front grille net can be removed if desired. To remove, follow these instructions: 1 To remove the grille, place your hands at the bottom of the grille and pull gently outward. Then do the same at the top to detach. 2 To reattach the grille, align the four holes on the grille’s back with the pins on the speaker and press in firmly. Connections 1 Switch off the power of your amplifier. 2 Connect the speaker cables to the input terminals on the back of the speaker. For input terminal polarity, red is positive (+) and black is negative (–). Loosen the knobs on the input terminals and insert the speaker cable wires into each of the terminal post holes, then tighten the knobs. 3 Connect the other ends of the cables to the amplifier’s speaker output terminals (for details, refer to your amplifier’s instruction manual). • You can also connect the speaker’s terminals with a banana plug. • When using a banana plug, first remove the caps covering the speaker terminal. • After connecting the plugs, pull lightly on the cables to make sure that the ends of the cables are securely connected to the terminals. Poor connections can create noise and interruptions in the sound. • If the cables’ wires happen to be pushed out of the terminals, allowing the wires to come into contact with each other, it places an excessive additional load on the amplifier. This may cause the amplifier to stop functioning, and may even damage the amplifier. • When using a set of speakers connected to an amplifier, you won’t be able to obtain the normal stereo effect if the polarity (+, –) of one of the speakers (left or right) is reversed. Non skid pad Speaker cable with white line Connect to the stereo amplifier's positive (+) output terminal. Speaker cable without line Connect to the stereo amplifier's negative (–) output terminal. CAUTION These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric shock when connecting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts. D3-4-2-2-3_A1_En For U.S. model Specifications Enclosure. . . . . . . . . . . . . . . . . . . . . . . . . . . . Bass-reflex bookshelf type Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-way Woofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 cm (3 15/16 in.) cone Tweeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.0 cm (3/4 in.) dome Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Hz to 40 kHz Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 dB Maximum power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 W Crossover frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 kHz Exterior dimensions . . . . . . . 135 (W) mm x 230 (H) mm x 220 (D) mm 5 5/16 (W) in. x 9 1/16 (H) in. x 8 11/16 (D) in. Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.9 kg (6 lbs 6 oz.) Supplied accessories Speaker cable (2.5 m (8.2 ft.)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Non-skid pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 set Safety support fixture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Screws for safety support fixture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warranty card Operating instructions (this document) • The S-CN301-LR is shipped with two speaker systems included. • Specifications and design are subject to possible modification without notice, due to improvements. © 2012 PIONEER CORPORATION. All rights reserve...