Assessments - 4, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Update your iPod with the latest software before using it. O iPod touch 2nd generation iPod classic o iPod 4th generation (color display) iPod nano 4th generation (video) iPod nano 2nd generation (aluminum) O iPod touch 1st generation iPod 5th generation (video) o iPod 4 th iPod mini generation a iPod nano 3rd generation (video) A * 1*1 ® © o o iPod nano 1st generation 69gb Precautions/Specifications Installing the unit on the wall The unit can be installed on the wall using the Wall-mount bracket SU-WL100 (not supplied). To customers Sufficient expertise is required for installing this product. Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety during the installation. Sony is not liable for any damage or injury caused by mishandling or improper installation, or installing any other than the specified product. Your Statutory Rights (if any) are not affected. To Sony Dealers The following instructions are for Sony Dealers only. Be sure to read safety precautions and pay special attention to safety during the installation, maintenance and checking this product. Before installing the unit on the wall • Make sure that the wall is strong enough to support the wall mounting. The wall should be able to support the weight of at least 20 times that of this unit. See “Specifications” (page 67) for the weight of this unit. • Make sure that the power cord is disconnected from the wall outlet. • Make sure that the screws remain securely tightened during the assembly process, to avoid the unit from falling or causing an accident. Safety information • Only qualified service personnel should carry out wall installations. • For safety reasons, it is strongly recommended that you use Sony accessories, including: — Wall-mount bracket SU-WL100 • It is strongly recommended that you use a Sony Wall-mount bracket in order to provide adequante air-circulation. 70GB 1 Adjust the position of the holders of the Base Plate. O Remove the screws that secure the left and right holders to the Base Plate and move the holders to the inner position. Q Firmly secure each holder using the screws removed in the previous procedure O. [Note] When using an electric screwdriver, set the torque setting to approximately 1.5 Nm (15 kgfcm). 71GB Precautions/Specifications 2 See "System installation dimensions diagram" (page 77), to determine the installation location. Allow for suitable clearance between the unit, ceiling and any protruding wall parts as shown below. Unit: mm Never install the unit set as shown below: Air circulation is blocked. 72GB 3 Secure the Base Plate to the wall using 4 or more 6 mm diameter or equivalent screws (not supplied). Select 4 screw holes with the mark shown in the diagram below and tighten the screws securely so that they will not become loose. Secure the Base Plate so that it is level. I & o o o o o o o o (8\ o 0 o O o 0 0 o Lo O Q_J Base Plate WARNING • The screws required for this procedure are not supplied. Select screws suitable for the material and structure of the wall. • If the Base Plate cannot be attached securely enough, use additional screws. • Be sure to confirm that the Base Plate is securely attached to the wall. 4 Detach the stand from the unit. O Remove the 2 screws that secure the stand from the unit. e Push the 2 tabs located on the bottom of the stand, and pull up the stand to detach from the unit. [ Note 1 Do not remove the stand for any reason other than to wall-mount the unit. 73GB Precautions/Specifications 5 Secure the two Mounting Hook to the rear of the unit. O Secure the Mounting Hook to the rear of the unit temporarily, using the 4 screws (+PSW4 x 12) supplied with the Wall-mount bracket SU-WL100. e Be sure that screws are tightened securely with equal torque strength to the rear of the unit. CAUTION • Be sure not to use any screws other than the ones supplied (+PSW4 x 12) when securing the Mounting Hook. • Make sure that the Mounting Hook angle is set at 0 degrees, and install the unit parallel to the wall. Do not adjust the Mounting Hook angle. 6 Connect the cable(s) to the unit. Connect the cable(s) to the connectors on the unit. For details on cable(s), refer to “Connecting the antennas and power cord (main unit)” (page 13). WARNING Be careful not ot stumble over the power cord or connecting cable(s), as you may hurt yourself. 74GB 7 Install the unit onto the Base Plate. O Determine the holes of the Base Plate for latching the upper hooks of the Mounting Hook. e Hold the unit securely with both hands, and gently align it on the wall. 75GB Precautions/Specifications 8 Firmly secure the unit and the Base Plate using the 2 supplied screws (+PSW4 x 12). Secure the screws to the angle mark 0. [Note] When using an electric screwdriver, set to torque setting to approximately 1.5N'm (15 kgfcm). WARNING Be sure to tighte...
Este manual também é adequado para os modelos :Speakers - NAS-Z200DIR (5.41 mb)