Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
See page 1 for further details. Peripheral Electronics®, a division of AAMP of America™ 13160 56th Court Clearwater, Florida 33760 866-788-4237 in the US or 727-572-9255 ext.262 for international calls support@peripheralelectronics.com ©2005 AAMP™ of Florida, Inc. Table of Contents Pages CHAPTER 1-Getting Started 1.1 Introduction 1 1.2 Precautions 1 1.3 Programming the iSimple BMW Interface 2 CHAPTER 2-General Installation 2.1 Installation at CD Changer 3 2.2 Pre-Installation Checklist 3 2.3 Installation at CD Changer Location 3 CHAPTER 3 -Operation 3.1 Operation 4 3.2 Troubleshooting 5 3.3 Warranty 6 3.4 Warning 6 3.5 FCC Statement 6 Chapter 1- Getting Started 1.1 Introduction Thank you for purchasing Peripheral Electronics’® iSimple BMW interface. The iSimple BMW interface is designed to provide endless hours of listening pleasure through your vehicles’ factory radios. To ensure that your iPod performs correctly in your car, we recommend that you read this entire manual before attempting installation of the iSimple BMW interface. The iSimple BMW interface will allow you to connect your iPod to a factory radio that has the ability to control a CD changer. The iSimple BMW is designed to be used with Generation 3, 4, Mini and Photo iPods. 1.2 Precautions (Important, Please Read) UPDATING iPod FIRMWARE For proper operation of the iSimple BMW interface, your iPod must be updated with the most recent version of Firmware from Apple. This is done on your computer. To Update the software on the iPod go to Follow the directions on the website to complete the download. There is no charge for this update. PREVENTING DAMAGE TO YOUR VEHICLE OR iPod. To eliminate the risk of an electrical short, we recommend disconnecting the car battery in most vehicles, except in the following situations: • Vehicles equipped with on-board navigation should not have the car’s battery disconnected. Doing so may cause loss of memory settings. These settings would then have to be reprogrammed by an authorized car dealer for a fee to be paid by the vehicle’s owner. For these vehicles, we recommend extreme caution when handling exposed 12V power or ground wires/connectors. •Vehicles that incorporate a security-code protecting the radio. If the car’s battery or the radio’s power plugs are disconnected, the radio will not operate without re-entering the security-code. If you have access to the security-code, feel comfortable disconnecting the battery and the radio’s power connectors. Other wise, do not disconnect the battery and exercise extreme caution while handling exposed 12V power or ground wires/connectors. PROPER MOUNTING LOCATION Securely install the interface in a location free from; heat, humidity, moving parts or direct sunlight. Beware of hot-air flow from your vehicle’s climate control system. We recommend securing the interface to a suitable location, free of sharp metal edges, using; double sided tape, Velcro or wire ties. 1 Docking cable Vehicle specific harness iSimple BMW interface 1.3 Programming the iSimple BMW Interface Now that you have identified the correct harness and dip-switch configuration using the application guide, it is now time to program the interface. To program the interface, set the dip-switches located on the side of the interface (see Fig.1 below) to the congfiguration listed below. Switches are in their default setting of “off” in the up position and are turned “on” when switched down. Refer to the chart on the bottom of this page. This programs the iSimple BMW interface to the vehicle it is being installed in. The dip-switches MUST be set before the interface is plugged into the vehicle. Otherwise the iSimple BMW interface will not work correctly. Dip Switch Configuration Chart CONNECTOR / DIP SWITCH VIEW22-BRAND MODE HARNESS 8 7 6 5 1 2 3 4 Vehicle specific harness CDC or Changer OFF OFF ON ON OFF OFF OFF ON BMW Fig.1 Side view of Interface with dip switches 2 Chapter 2- General Installation 2.1 Installation at CD Changer The location of these CD changer cables will vary by vehicle. Some common locations of these cables are in the trunk, behind the glove box, and in or under a center console. 2.2 Pre-Installation Checklist At this time and before beginning the installation: • Your iPod’s Firmware should have been updated. (section 1.2) • You should have your radio’s security code.(when applicable, see section 1.2) • The dip-switches on the interface should have been set with the proper configuration. (see section 1.3) • You should have in your possession the correct harness for your vehicle. (see sec. 1.3) • You have determined your installation location. (see section 2.1) If any of these steps has not been taken, STOP. Only when ALL of these steps have been taken should you proceed with the rest of the installation. 2.3 Installation at the CD Changer Location In this section you will learn how to install the iSimple BMW interface in the factory CD changer location...