Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
..Place the DLA2/4/6 in the same equipment location as the Receiver/Amplifier. ..Turn off all power to the Receiver/Amplifier and make sure the DLA2/4/6 power supply is unplugged! ..Strip approximately 3/8" of insulation from the ends of all speaker and control wiring. Twist the exposed end of each speaker wire to ensure that no loose strands remain. * If applicable. Cat5 is used for touch pad and IR receiver wiring 3/8" Speaker Wire Cat5 Wire 3/8" A Stereo Receiver with "A/B" 1 Choose Receiver/Amplifier Type Home Theater Receiver with "A/B" 2 Connect Speakers 3 Choose Method of Control Optional RF RECEIVERTOUCH PADSIR RECEIVERS ++––+–+– C Home Theater Receiver with "Zone 2" Connect the RF Receiver to the ATON Port IR S G V White/Green (+12V) Brown (Ground) Orange (Status) White/Blue (IR) Cat5 Wire Splice to Cat5 Wire To local speakers To DLA input Connect to the "Zone 2" speaker terminals. To DLA input NOTE: Refer to your receiver manual for help activating your "Zone 2" speaker outputs. + – + – L R + – + – Connect to the "B" speaker terminals. To local speakers To DLA input Red Black White Yellow (Do Not Connect) White/Green (+12V) Brown (Ground) White/Blue (IR) + – + – + – + – L R L R + – + – + – + – Connect to the "B" speaker terminals. Speaker Wire Speaker Wire Speaker Wire Be sure to connect the positive speaker wire to the positive input of the speaker and the negative speaker wire to the negative input of the speaker. RJ11 Set Impedance Dipswitches. Amplifier Dipswitch: Set to Receiver/Amplifier Impedance – 8 or 4 Ohms. (Refer to receiver/amplifier manual for its specific impedance) Speaker Dipswitch: Set to Average Speaker Impedance – 8 or 4 Ohms. (Refer to each speaker manual for its specific impedance) Plug in the DLA2/4/6 Power Supply. Adjust the Receiver/ Amplifier volume to the lowest lev Please consult your owner's manual for additional installation examples, applications and safety instructions. er/ el.el. Turn on the Receiver/ Amplifier and start audio source (CD player radio, etc.). Powe Star Audio Source Receiver/Amplifier Volume Knob 4 5 6 7 Finally, turn on each room from the front panel of the DLA2/4/6 and adjust to a comfortable listening level. 12While listening to the room tur on in the previous step, slowly adjust the Receiver/Amplifier volume to a level that is the loudest it can play in the room without distor or clipping. Make a note of the volume level for future reference. ned adjust to n tion e ce. 11 Set the Receiver/ Amplifier to stereo mode and disable any surround sound or DSP "Sound Fields." 8 Turn on one room from the front panel of the DLA2/4/6 and adjust volume level to maximum. 109 Receiver/Amplifier Volume Knob WARNING! Do not connect speakers to the DLA2/4/6 that have an impedance value lower than what is supported by your receiver/amplifier. In doing so, you run the risk of overheating and damaging both the DLA2/4/6 and your receiver/amplifier! Consult speaker and receiver/amplifier manuals for their specific impedance ratings. If using a Receiver with "A/B" speaker outputs: .................................................................................... the speakers connected to the DLA .................................................................................... both the "A" speakers and those connected to the DLA OR NOTE: When using the "A+B" setting the receiver volume will need to be adjusted accordingly When the DLA2/4/6 is not in use, turn off the "B" speakers and turn on the "A" speakers for normal stereo/surround sound listening ! B Start Here ..Run all speaker wiring (16 gauge is recommended) and control wiring (Cat5)* to the DLA2/4/6. Be sure to label the wires for easy identification. ..Place the DLA2/4/6 in the same equipment location as the Receiver/Amplifier. ..Turn off all power to the Receiver/Amplifier and mak...
Este manual também é adequado para os modelos :Speakers - DLA DLA2 (400.27 kb)