Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
When the beginning of the scene stored in the computer is missed: Enter a larger value than 1.30. •Factory preset is 1.30 sec.. 4 4 DETERMINE VALUE Click "OK". •This value is stored in the computer. 5 5 CHECK EDIT-START TIMING AGAIN To check the corrected edit-start timing, dub the stored scenes and play them back. NOTE: Even if the edit-start timing is adjusted, there can be a slight margin between the adjusted edit-start point and the dubbed scenes' one. MOVIE PLAYER FILE MEMO ID CUT OUT STARTSCENE 00:10:04:28F IN/OUT MODE STILL PLAY SEARCH SLOW FF REW 00:00:01:20F 06 00:01:30:12F 00:07:15:21F 00:15:50:11F 00:03:27:14F 00:10:40:18F 00:20:33:10F FileVideo Printer HelpEdit travel Europe Tour New Open Save Save As... ID Change Device Change Name Change Pause Time... Open VCR Control Window Close Serial Initialize Counter Reset Exit Ctrl+N Ctrl+O Ctrl+S Ctrl+A File Pause Time Correction OK CANCEL Type in the value from 0.00(sec) to 2.60(sec), to adjust pause time during editing. Pre-start time = 1.30 (sec) 65TROUBLESHOOTING 65TROUBLESHOOTING MESSAGE v POSSIBLE CAUSE m CORRECTIVE ACTION Error – – This application will v The COM port used for the JLIP connector is not close. selected, or the COM port is selected but the Check devices – – Confirm connection is wrong. that power is ON. m Check the connected COM port and select it on the "Serial Port Selection" screen (Z pg. 46). No devices detected to v Power is not supplied or the connection is wrong. connect. m Connect the devices correctly and turn them on Power ON all devices in (Z pg. 42, 43). system. Communication error v Device is not turned on or cable is disconnected. (&H (number)) m Connect the device correctly and turn it on Check cable connection. (Z pg. 42, 43). m If device was turned off and on again during operation, click "OK". All devices should function properly. Select the device to control. v The line where the name of the device to use appears is not clicked. m Click on it and "OK" (Z pg. 47). No video cassette!! Load a video cassette to ID (number). v The video cassette is not loaded in the camcorder. When the video cassette is removed during operation, this message appears. m Insert the video cassette into the camcorder. Invalid entry in scene v The value of the CUT OUT point is smaller than (number) (There is IN > OUT the CUT IN point's. condition). Correct the time m Set the value of the CUT OUT point so that it is or delete the scene. larger than the CUT IN point's (Z pgs. 50, 54). Select a number between 0 v When correcting the CUT IN/OUT points, the and 24. value you set differs from the original by over 25 frames. m Select integral number from 0 to 24 (Z pg. 54). Invalid frame number on drop frame counter. v Because the DV-format digital camcorder uses the drop frame system, inputting frame 00 and 01 is impossible. m Input frame value other than 00 or 01 (Z pgs. 48, 54). The monitor displays of the application software illustrated in this manual may differ from those you are actually viewing depending on the operating environment of your computer. MAJOR SPECIFICATIONS JLIP VIDEO CAPTURE DOCKING STATION Connectors S-Video : Output Y : 1.0 Vp-p, 75 ohms (S2 output) C : 0.3 Vp-p, 75 ohms Video : Input 1.0 Vp-p, 75 ohms (pin jack) (CAPTURE INPUT (EXT.)/PRINTER connector) : Output 1.0 Vp-p, 75 ohms (pin jack) (VIDEO output connector) Audio : Output –8 dB, 1 kiloohm (pin jack) JLIP (x 2) : 3.5 mm dia., 4-pole, mini-head jack (compatible with EIAJ RC-5325 plug) Digital : Mini DIN 8-pin Multi-connector : 34-pin Editing connector : 3.5 mm dia., 2-pole DC output : 5 V DC Captured image sizes : 768 x 552 pixels, 80 x 60 pixels Operating temperatures : 5 to 30° C Dimensions : 113W x 61H x 145D mm Weight : Approx. 395 g Power supply : 6.3 V DC *E. & O. E. Design and Specifications subject to change without notice. 67INDEX 67INDEX A Arrange Index ................................. Z pg. 31 Automatic Capture (AUTO) ....... Z pg. 26, 28 B Bitmap ...................................... Z pg. 24, 30 C Capture Mode................................. Z pg. 30 Change ID ................................ Z pg. 31, 62 COM Port ................................. Z pg. 17, 46 Counter reset .................................. Z pg. 32 Counter Value Change.................... Z pg. 32 Create New Folder ......................... Z pg. 33 D Delete Index Image and Full Image ........................................................ Z pg. 31 Desktop Window................ Z pg. 20, 48, 56 Device Selection ............................ Z pg. 18 Dubbing ......................................... Z pg. 52 E Edit Menu ....................................... Z pg. 22 Exit (Close)...................................... Z pg. 19 F Field Picture ................................... Z pg. 30 File Menu ....................................... Z pg. 22 Frame Picture ........................... Z pg. 21, 30 Full image data ............................... Z pg. 21 H Help Menu .................
Este manual também é adequado para os modelos :Speakers - LYT0002-0J9A (1.2 mb)