Assessments - 4, GPA: 3.3
(
)
)
|
Facilidade de uso
2) Follow all instructions 3) Keep these instructions 4) Heed all warnings 5) Do not use the MATRIX 1000 near water. Be extra cautious when moving the system during rain or while transporting the system over wet surfaces as water might splash onto the amplifier. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with manufacturer’s instructions. 8) Do not install near heat sources such as radiators, stoves or other devices that may produce heat. 9) Do not defeat the safety purpose of the polarization or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched, particularly at the plug and the point where it exits the MATRIX 1000 amplifier. 11) Only use attachments / accessories specified by B-52 Pro-Audio. 12) Use caution when transporting the system to avoid injury from tip-over. 13) Unplug the MATRIX 1000 during lightning storms and when not in use. 14) Refer all servicing to qualified to personnel. Servicing is required when the MATRIX 1000 has been damaged in any way such as when power-cord or plug is damaged, liquid has been spilled into the cabinets, the unit has been exposed to moisture or rain, does not operate normally, or has been dropped. 15) To reduce the risk of fire or electric shock, do not expose the MATRIX 1000 to rain or moisture. 16) The MATRIX 1000 is not intended for outdoor fixed installations or in high moisture areas. Moisture can damage the speakers and can use cause corrosion of electrical contacts. Keep speakers out of extended or intense direct sunlight. The subwoofer spider and surround will prematurely dry out and finished surfaces may fade and be damaged by long- term exposure to intense ultra-violent light. CAUTIONCAUTION RISK OF ELECTRIC SHOCKRISK OF ELECTRIC SHOCK DO NOT OPENDO NOT OPEN HEED ALL WARNINGS WARNING: To reduce the risk or fire or electrical shock do not expose this equipment to rain or moisture. AMPLIFIER SPECIFICATIONS: Subwoofer Power Output: 10” Two-way Power Output: Line in: Parallel out: Input Impedance: Speaker Out: ACTIVE CROSSOVER: Crossover Frequency: SUBWOOFER: Speaker: Nominal Impedance: Subwoofer Freq. Response: 400 W / 8 Ohms @ 1% THD 150 W / 4 Ohms @ 1% THD XLR Female XLR Male 48 k Ohms Speakon NL4 Style Connector 120 Hz; 24 dB/ Octave 1 x 15” Custom Built B-52 Subwoofer 8 Ohms 40 Hz – 120 Hz +/- 3dB Sound Pressure Level (1w/1m): 102 dB (half space) Max. SPL: 127 dB @10% THD Weight: 115 lbs Dimensions (Transport): 28” (H) x 19” (W) x 23” (D) 10” TWO-WAY SPEAKERS: Speaker Input: Speakon style connector (pin 1+ = +, pin 1- = -) LF/MF Woofer: 1 x 10” Custom Built B-52 Transducer HF Driver: 1 x 3/4” Titanium Diaphragm on CD Horn HF Dispersion: 90O x 40O Nominal Impedance: 4 Ohms Active Freq. Response: 120 – 19K Hz +/- 3dB Crossover Frequency (passive): 2.5 kHz; 12 dB / Octave Sound Pressure Level (1w/1m): 101 dB (half space) Max. SPL: 124 dB @10% THD Weight: 25 lbs Dimensions (Upright): 19” (H) x 12” (W) x 11” (D) COMPLETE SYSTEM: Weight: 165 lbs Dimensions (Transport): 39” (H) x 19” (W) x 23” (D) Note: Specifications are subject to change without notice The Matrix 1000 Active Speaker System Congratulations on your purchase of this B-52 Professional Matrix 1000. The MATRIX 1000 system is a complete sound reinforcement solution consisting of two 10” two-way speakers and an active 15” subwoofer. The subwoofer enclosure is equipped with a three channel amplifier and all the electronics required to run the system. The electronic circuitry was fine tuned to match the two-way speakers for the best possible sound. This system was designed for easy operation since you do not need to worry about tweaking frequencies and finessing levels. All you have to do is set up the system components, connect the XLR right and left signal cables, speaker cables and power cords and you’re ready to go. SUBWOOFER: The 15” subwoofer enclosure is divided into two separate compartments. The front chamber serves as the cabinet for the 15” subwoofer. The rear chamber houses all of the system’s electronic circuitry, which includes the amplification for all three components, power supply and preamps. The 15” subwoofer has a power handling capability of 400 watts and a nominal impedance of 8 ohms. 10” TWO-WAY SPEAKERS: The two 10” two-way speakers are loaded with B-52’s custom 10” speakers and a 3/4” titanium diaphragm compression driver, mounted to a 900 x 400 constant directivity horn. The speakers are designed to be pole mounted, can sit as stage monitors and have built-in (3/8” – 16 TPI) flying hardware for permanent installations. The front panel of both two-way speakers is con- caved so as to fit perfectly onto the s...