Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
2 seconds. You will hear 2 beep tones to confirm the station is stored. 3. To preset another station, repeat above steps. To change the preset station, tune into the desired station and hold down the Preset Button. The new station will replace the previous station. Tuning into a Preset Station 1. Turn on the unit and press the Mode Button on the iH30 or the remote control to turn on the radio. 2. Press the desired Preset Button. The corresponding station will show on the display. 3. Press the Volume+ and Volume– Button on the iH30 or the remote control to adjust the system volume. 4. To turn off the unit, press the Power On/Off Button on main unit or remote control to turn it off. Operating the Remote Switch To save battery power, switch off the Remote On/Off Switch for longer battery life. The switch function while using the AC adaptor. Headphone Jack Connect a headphone Headphone Jack in the front of the unit for The built-in speakers shut off when the headphone 13 Trouble Shooting Symptom Possible Problem Solution Unit doesn’t respond (no power) AC adaptor isn’t plugged to a wall outlet or the connector is not plugged into the power supply jack on the back of the unit Plug the AC adaptor into a wall outlet and plug the connector into the power supply jack on the unit Wall outlet is not functioning Plug another device into the same outlet to confirm the outlet is working iPod cannot dock properly Using no or wrong iPod insert Make sure the dock insert is the proper fit for your iPod iPod is not installed properly Remove your iPod from the dock and check for any obstruction on the connectors in the dock and on your iPod. Then reseat it in the dock. iPod does not respond to the unit iPod is not installed properly Remove your iPod from the dock and check for any obstruction on the connectors in the dock and on your iPod. Then reseat it in the dock. Your iPod software is too old Upgrade software on your iPod. For details, visit iPod is locked up Please make sure your iPod is working properly before docking it to the unit. Please refer to your iPod manual for details on iPod operation. Using 1st or 2nd generation iPod, iPod Shuffle or other device iH30 cannot control those iPods or other devices. 14 Trouble Shooting Symptom Possible Problem Solution iPod didn’t charge up iPod is not installed properly Remove your iPod from the dock and check for obstruction on the connectors in the dock and on your iPod. Then reseat it in the dock. iPod is locked up/frozen Please make sure your iPod is working properly before docking it in the unit. Please refer to your iPod manual for detail. iPod battery has problem Sound is distorted Volume level is set too high Decrease the unit and/or iPod Shuffle volume Sound source is distorted If iPod original sound source is poor quality, distortion and noise are easily noticed with high-power speakers. Try a different audio source such as a music CD. If you are using an iPod Shuffle or external sound source like older generation iPod, try reducing the output volume on the device itself. Also, try turning bass boost OFF. Remote Control didn’t work Battery weak Replace with new battery Remote Control is not pointed toward the IR sensor Point the Remote Control toward the IR sensor, within 10 feet of the unit. Remote On/Off Switch is activated Move Remote switch to ON position 15 Solucionando problemas Sintoma Causa Solucion La unidad no funciona (no circula corriente electrica) El adaptador de AC no esta conectado al tomacorriente o el conector no esta conectado a la ficha en la parte posterior de la unidad Conecte el adaptador de AC al tomacorriente y tambien conecte el conector a la ficha en la parte posterior de la unidad El tomacorriente no funciona Coloque otro aparato en ese mismo tomacorriente para confirmar si el que no funciona es el tomacorriente El iPod no encastra correctamente No ha colocado el encastre del iPod, o esta utilizando el encastre incorrecto. Verifique que el encastre sea el apropiado para su iPod El iPod no encastra correctamente Quite el iPod del encastre y retire la posible obstruccion del encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre. El iPod no se comunica con la unidad El iPod no esta instalado correctamente Quite el iPod del encastre y verifique posibles obstrucciones del encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre. Su software es obsoleto Renueve su software. Para mayor informacion, dirijase a El iPod no responde Verifique que su iPod funcione correctamente antes de conectarlo a la unidad. Refierase al manual iPod para mas detalles. Usted tiene un iPod de primera o generacion, un Shuffle u otro tipo de aparato El iH30 no puede controlar estos otros aparatos 1 Solucionando problemas Sintoma Causa Solucion El iPod no carga El iPod no esta instalado correctamente Quite el iPod del encastre y retire la posible obstruccion del encastre o d...