Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
4:time 5:iPod/ iPhone 2:antenna 6:radio 3:inserts1:power .............. 2 .. 5 Install/Replace Backup Battery The iP99 uses a backup battery system to provide continuous alarm operation and clock settings in the event of a power failure. If the Battery Low Icon located on the right of the display is on, it is time to replace the backup batteries. Please make sure the AC adaptor is connected, otherwise all settings may be lost during battery replacement. Open the battery compartment cover located on the bottom of the unit. Insert 2 “AA” batteries as indicated. We recommend the use of alkaline batteries for longer life. Batteries information: • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon -zinc) or rechargeable (nickel-cadmium) batteries. Replacing iP99 Backup Batteries Using the iP99 Radio Setting up Antennas a) Snap AM loop antenna into provided stand, then plug AM antenna cable into AM Loop Antenna socket on back of unit. Move antenna away from unit for best reception. b) Extend FM Antenna (on back of unit) fully for best reception. Do not strip, alter or attach to other antennas. c) Locate iP99 and all antennas away from AC adaptor in wall socket (at least 3 feet) for best radio reception. Tuning and Playing the Radio a) Press the Radio Button to select radio play mode. Press as needed to select FM or AM radio band. b) Turn the Set Wheel to tune radio to a desired station. c) To program the current station as a preset, press and hold Preset Button 1-2 until P1 flashes on display; press again for P2 and allow to time-out (beep confirmation). Repeat steps a,b,and c for other preset buttons to preset up to 12 stations (6 AM, 6 FM). To listen to a preset station at any time, simply press the desired preset button once or twice. d) Turn the Volume Wheel to adjust iP99 volume up or down. e) Press the EQ Button to select Treble, Bass, SRS WOW sound effect or Balance. Turn the Set Wheel to adjust settings. EQ settings for iPhone/iPod and radio mode are independent. f) Press Alarm Reset/Power Button to turn iP99 off. Using the Line-in Jack a) You can play nondocking iPod models or other audio devices through the iP99 Line-in Jack, connect one end of a patch cord (available at ihomeaudio.com..in the device’s line out or headphones jack, the other in the iP99 line-in jack. Make sure there is no iPhone/iPod docked in the iP99 when using the line-in jack. b) To listen to your audio device, press the Radio Button until “line-in” is displayed, indicating line-in mode. Adjust the output volume on your line-in device. Using Sleep Mode Sleep mode lets you sleep to your iPhone/iPod or the radio, gradually lowering the volume until the unit shuts off at the selected time. a) Press the Sleep Button to select an amount of time before the iP99 shuts off: 120, 90, 60, 30 or 15 minutes. b) Turn the Volume Wheel to set the sleep volume (this volume setting is separate from your standard volume setting). Using the Dimmer a) Press the Snooze/Dimmer Button during normal operation to adjust brightness of LCD display. There are 8 levels of brightness including OFF. When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. 2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, that may impede the flow of air through the ventilation openings. 3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat. 4. Power Sources – The unit should be connected to a power AC adaptor of the type described in the operating instructions or as marked on the appliance. 5. Power-Cord Protection – Power AC adaptor cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. It is always best to have a clear area from where the cord exits the unit to where it is plugged into an AC outlet. 6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning instructions. 7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product. 8. Att...