Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
New York 11788 Telephone (516) 231-7750 Cable Address: Audiovox Hauppauge, N. Y. / TWX: 96-7794 These speakers have been designed for use with all car stereo systems and incorporate the following deluxe features: 1. Modern, glare-broof cabinets blend well with any car decor. 2. Unique 5 inch round free edge speaker fully emphasizes .stereo effect, reproducing both high and low tones in rich volume and with minimal distortion. 3. Maybe mounted either in door panels or on rear deck. 4. May also be used with car radios as well as stereo tape systems. Installation Instructions A. DQor Panel Mounting 1. For door panel mounting, only the top portion of the speaker enclosure (cabinet A in diagram) is used. 2. Locate a convenient place on the door panel for the speaker to be mounted. Note: Care should be taken to make sure speaker installation will not obstruct the raising or lowering of the window or effect the door locking mechanism. 3. A hole Z inches by 2 '/2 inches should be made in the door panel, and in the sheet metal behind the door, if necessary, to provide clearance for the speaker magnet. 4. Th~ wire lead from the speaker should be fed through the door and routed towards the location of the stereo or radio. 5. The speaker may now be mounted on the door panel using the four black self-tapping screws which previously held the two portions of the speaker enclosure together . B. Rear Deck Mounting 1. For rear deck mounting, the speakers may either be"jnstalled flush against the deck or within the wedge. shaped enclosures to direct the sound forward. For flush mounting, proceed according to A above (Door Panel Mounting). For wedge installation proceed as follows. 2. Separate the two speaker enclosures as far as possible on rear deck to preserve stereo effect. 3. Separate the enclosure portions (Cabinet A and Cabinet B) by removing the four black screws. 4. Using cabinet B as a template, mark the locations of the three mounting holes and the large square hole on the rear deck, as shown in the diagram. 5. Cut out the large hole and the three small holes and mount Cabinet B on the rear deck using.the screws and nuts provided. 6. The wire lead should be fed through the large hole and routed towards the location of the stereo or radio. 7. Remount Cabinet A on Cabinet B using the four black self tapping screws previous Iy removed c. Wiring 1. When routing speaker wires, make sure they are not pinched or cut by any bare metal edges. 2. Splice the leads from the speakers to the output leads of the tape deck or radio, making sure to observe and maintain the polarities of the left and right channels. Cover all exposed wires with electrical insulating tape. 3. When attaching two speakers to one output channel, correct impedance matching must be maintained. between the speakers and the stereo or radio. Two 8 OHM speakers wired in parallel: 4 OHMS Two 4 OHM speakers wired in series: 8 OHMS Speaker Rating 5 inch round, 7 oz. magnet Loudspeaker: 40HMS Impedance Mounting Applications Side door panels, rear deck, etc REAR DECK SPEAKER INSTALLATION DIAGRAM 1 , --Black screw 3 Screws , t .-, -..Cabinet A with Loud speaker PRINTED IN CHINA .fiWt.fie as jt( I. Remove Plastic Shipping Caps from Generator Components. Assemble Generator Components as illustrated below, EXCEPT the *STAMPED NUT (5/8-18). See Note I 2. You will need to work where the Vehicle Speedometer Cable is attached to the Transmission. If necessary. raise the vehicle. Chock Wheels. ,B~not get ~d~,r,~Yvehicle held~p by.ajacko,~~-,Us~Jack Stands or Ramps-, ":l:JI;eweb,9.,,a,~9~c~~teblockWiU ,n9{ car-,,'I)ONOT,RISK,YOUR LIFE! " " , "'"", ' ,I""", ",I" "" ' " ' " , 3. A. Disconnect Vehicle Speedometer Cable from Transmission. B. Connect Speedometer Cable to TANG DRIVE ADAPTER. Seat Speedometer Cable into TANG DRIVE ADAPTER Slot, tighten Speedometer Cable. See Note .I c. Install Generator Assembly into transmission housing. Turn SIGNAL GENERATOR so wires will not catch on objects while driving. Tighten Nut. TO EXISTING SPEEDOMETER CABLE - NOTE .I After Cable is assembled, inserlADApTERKEYintoother end and rotate Drive Cable. If Cable will not rotate, remove TANGDRIVEADAP:TERandinsta11*STD NUT (5/8-18) in position shown. Reinstall TANG])iu\iE ADAPTER. This will allow clearance betWeen Speedometer Drive Cable Inner Core Wire and SIGNAL GENERATOR Assembly. Form# 2097 6199 Rev B 4. Plug ExTENSION into SIGNAL Lead. Select:proper plastic connector for system HARNEss GENERATOR being installed and insert terhiinals of ExTENSIOl:lHARNEssLead into plastic CONNECTOR as shown. For Cruise Control Systems using Signal Generator Harness to Main Wiring Harness connection, use HARNEssCONNECTOR and insert wires as shown. ~~:::s HARNESS CONNECTOR For Cruise Control Systems using Signal Generator Harness to Module connection, use MODULE CONNECTOR and insert wires as shown. MODULE CONNECTOR 5. Route wires using Wire Ties to support wires, as necessary.keeping them away from any Hot, Shar...