Assessments - 3, GPA: 4.7 ( )

Fabricante : Audiovox Arquivo Tamanho: 625.36 kb Arquivo Nome : Língua de Ensino:

Make certain you apply sealant (not included) as shown. 4. Assemble radio mounting plate assembly to bolt studs as shown. 5. Complete wiring. 6. Place housing below radio plate assembly and connect speaker wiring to radio wiring. 7. Secure housing using six screws and washers provided. 8. See Fig. 4 if installing CElOO/CE200/CE300. Fig. 4 Installation 1. For figure I installation: Follow steps 1-11 then refer to Fig. 4 and follow instructions below it. 2. For figure 2 installation: Follow steps 1-9 then refer to Fig. 4 and follow instructions below it. 3. For figure 3 installation: Follow steps 1-7 then refer to Fig. 4 and follow instructions below it. Figure 4 Installation: Only for CElOO/CE200/CE300 I. The entire housing and mounting plate (less radio) should now be secured to the roof as shown in Fig. 4 2. Insert mounting sleeve into housing opening and bend all tabs outward to secure it. 3. Reach through opening to access radio wimg connector and plug into radio. 4. Reach through opening to access antenna lead and plug into radio. 5. Pre-test radio. 6. Slide radio into housing until locked in place. FIG. A FIBERGLASS CAP ROOF ( CROSS SECTION OF ROOF) RBERGLASSROOF CAP STEEL ROOF :":,.:;:c;:;:;c:;,,;;.:c:.:'ii:::i FIG. A DISASSEMBLY: AIR GAP 1. Remove molded inside headliner prior to installation AIR GAP 2. Do not remove the fiberglass roof cap See F1g. 1. for Installation LMOLDED HEADLINER FIG. B STEEL ROOF WITH HEADLINER {CROSS SECTION OF ROOF) FIG. B DISASSEMBLY: 1. Remove molded inside headliner prior to installation Note: If the air gap (space) between the steel roof and the headliner is less than 1/4" , refer to Fig. C See Fig. 2 for Installation FIG. C STEEL ROOF ONLY (CROSS SECTION OF ROOF) r; STEEL ROOF FIG. B DISASSEMBLY: 1. If the roof has an inside headliner that is either flush or has an air gap of less than 1/4" , do not remove the headliner L NOTE: SOME OF THESE TYPES See FIg. 3 for Installation OF ROOFS HAVE A HEADLINER THAT IS GLUED TO INSIDE OF THESE OF THE ROOF (NO GAP IS IN RG. C) FIG. 1. INSTALLATION , (INSERT AFTER ""' INSTALLATION IS WRENCH(INCLUDED) -COMPLETED) USE I SEALANT TO INSURE ~ / A LEAK-FREE SEAL / ~ ~ / STEEL CUP WASHERS I MOUNTING BOLT (SELECT LENGTH """" NEEDE FROM CHOICE OF LENGTHS ,..,.. INCLUDED) I DRILL 5/16. /r~MMEIS DIA. HOLES PER ~ - TEMPLATE -;----- APPLY A BEAD OF SEALANT AROUND / BOTH SIDES / - OF HOLES ~ FLAT WASHERS ~..-JAM NUTS (TIGHTEN ARMLY) ~ STEEL PLATE ~~ I ~ USE THESE HOLES FOR CASE 580K / ./ USE THESE HOLES / ~ FOR ALL OTHER EQUIPMENT ~ ~.J BLACK WASHERS --( 6 PCS.) , , , ~ ~ , , #6 BLACK SCREWS TRIMPLATE (6 PCS.) ~==-PLASTIC HOUSING ~0 0..,.. RADIO SHAFT NUTS ~ ~~ FIG. 3 INSTALLATION WRENCH (INCLUDED) ~ MOUNTING BOLT (SELECT LENGTH NEEDE FROM CHOICE OF LENGTHS INCLUDED) ' I G / STEEL CUP WASHERS RUBBER GROMMETS DRILL 5/16" DIA. HOLES TEMPLATE PER ~ I ~ APPLY A BEAD OF SEALANT AROUND BOTH SIDES OF HOLES ,,) ~ ~ ~..- - FLAT WASHERS JAM NUTS (TIGHTEN RRMLY) STEEL PLATE ~ ~~ USE THESE HOLES ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :