Assessments - 3, GPA: 4 ( )

Fabricante : Directed Audio Arquivo Tamanho: 746.89 kb Arquivo Nome : Língua de Ensino:

For mid-bass/midrange settings, try to keep the setting low enough to keep your sound stage in front of you, without overdriving the speaker. It will be to your advantage to spend some extra time with this adjustment, listening to familiar music or system set-up discs to achieve the kind of musical reproduction that you prefer. • The gain adjustment allows you to set proper signal match for clean, quiet amplifier operation. For full-range and simultaneous stereo/mono bass applications, start by playing some music you are familiar with. With the gain adjustment on the amplifier in the middle of its rotation, bring up the volume on your head unit to the 3/4 volume setting or until you start to hear distortion or clipping. If you hear distortion before you reach the 3/4 volume setting of your head unit, reduce the gain setting on the amplifier and start to raise the head unit volume again. When you can listen to the music at or slightly above 3/4 on your head unit without audible distortion, slowly raise the gain of the amplifier until distortion is heard, then back off the gain until the distortion is not audible. This setting will allow you to reach full output with all but the quietest of source material, while avoiding excessive noise in the system. • The same procedure should be used for adjusting the amplifier when the on-board crossover is set to LPF or HPF, but you will also have to take into consideration the effect that gain adjustment has on system frequency response and imaging. Again, plan on spending some time with music that you know, getting the gain and crossover settings the way you like. Test discs and analyzers may help with this process, but in the end it's your ears that count - listen to the music! © 2003 Directed Electronics, Inc REAR PANEL CONNECTIONS 1. S SSp ppe eea aak kke eer rr O OOu uut tt T TTe eer rrm mmi iin nna aal lls ss - Connect the speakers to these terminals. (Refer to the Speaker Connection section of this guide.) 2. P PPo oow wwe eer rr F FFu uus sse ee - --This fuse protects the amplifier against internal electrical damage and is meant to protect the amplifier only. All other power connections should be fused at the 5. source. 3. ( ((+ ++) )) 1 112 22 V VVo ool llt tt P PPo oow wwe eer rr - Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of the vehicle battery or the positive terminal of an isolated audio system battery. W WWA AAR RRN NNI IIN NNG GG: ::Always protect this power wire by installing a fuse or circuit breaker of the appropriate size within 12 inches of the battery terminal connection. 4. R RRe eem mmo oot tte ee T TTu uur rrn nn O OOn nn - This terminal turns on the amplifier when (+) 12 volt is applied to it. Connect it to the remote turn on lead of the head unit or signal source. If a (+) 12 volt remote turn lead is not available, a Remote Power Adapter (P/N #55000) can be used to supply a remote turn on signal. DO NOT connect this terminal to constant (+) 12 volt. G GGr rro oou uun nnd dd - --Connect this terminal directly to the sheet metal chassis of the vehicle using the shortest wire necessary to make this connection. Always use wire of the same gauge or larger than the (+) 12 volt power wire. The chassis connection point should be scraped free of paint and dirt. Use only quality crimped and/or soldered connectors at both ends of this wire. DO NOT connect this terminal directly to the vehicle battery ground terminal or any other factory ground points. © 2003 Directed Electronics, Inc © 2003 Directed Electronics, Inc 11 SPEAKER CONNECTIONS MONO CHANNEL 1500X FUSES SPEAKER 4 Ohm SPEAKER 4 Ohm TWO SPEAKER CONNECTION FUSES SPEAKER 2-4 Ohm ONE SPEAKER CONNECTION 25A fuses 25A fuses 12 © 2003 Directed Electronics, Inc TWO CHANNEL 2300X FOUR CHANNEL 4600X BRI BRI FUSES Note that the two speakers & four speakers have been connected to the four terminal following the (+) and (-) graphic. Your speaker terminals may be marked (+) and (-) or there may be red dot by one terminal which means the same as (+). Connecting the speakers in this manner assures that the two speaker cones will move in and out together according to the original recording. If one of the two speakers is reversed, stereo imaging and bass response will be degraded. 25A fuses 25A fuse © 2003 Directed Electronics, Inc 13 BRIDGE MODE TWO CHANNEL 2300X SPEAKER 4 Ohm FOUR CHANNEL 4600X BRI BRI FUSES SPEAKER 4 Ohm SPEAKER 4 Ohm Note that the two speakers & four speakers have been connected to the four terminal following the (+) and (-) graphic. Your speaker terminal may be marked (+) and (-) or there may be red dot by one terminal which means the same as (+). Connecting the speakers in this manner assures that the two speaker cones will move in and out together according to the original recording. If one of the two speakers is reversed, stereo imaging and bass response will be degraded. 25A fuse 25A fuses SPECIFICATIONS Xtreme models 1500X 2300X 4600X Type Mono blo...

Baixe o seu

Para fazer o download, introduza 2 dígitos :