Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Different considerations are needed when choosing the locations that best suit your needs. The locations must be large enough for the speakers to fit. Care is needed to ensure that the location you have chosen will not affect any of the mechanical or electrical operations of the vehicle. Determining the best location for the speakers will depend on your cosmetic needs and your vehicle's interior. If minimal intrusion in your vehicle is desired, factory speaker locations may be the ticket for you. Placing the speaker in the factory location can often give very desirable results. Door Mounting When checking for possible speaker locations in the doors, check the operation of the window and all assemblies. There is also a stabilizer stop bar in between the door and the door jamb. This bar prevents the door from opening too far. Many shade tree installers overlook this and check for clearance only when the door is fully open. Figure 1Figura 1Abbildung 1Stagger the holes for the wiring and use a rubber grommet to protect the wire from damageFigure Door BodyFront DashKick PanelSpeakercut-outTo DoorSpeakercut outCoaxialDriverDampening MatSpeaker installedwith no gapsor air leaksDampening ontop of outerdoor skinDoorPanelRear/Trunkof CarRear Rear Deck Mounting In rear deck installations, check the operation of the trunk suspension springs or tension bars. These tension bars move in the opening and closing of the trunk. You cannot be too cautious during this part of the installation, In addition, do not locate the speakers too close to the back of the rear deck. Installing the far screws will only be possible with the removal of the rear window. Figure 2Figura 2Abbildung 2Stagger Trunkof CarRear SeatGrilleScrews Installing the Mid/Woofers Step 1: Determine where the speakers will be mounted. Make sure there is a flat area large enough for the speakers to fit properly. An uneven mounting surface can damage the driver. Step 2: Check to make sure the space you have chosen for the speakers will not interfere with the operation of the vehicle. Step 3: Using the supplied template guide, mark the mounting hole and mounting screw hole locations with a pen for each speaker. Step 4: Cut the holes for the speaker. When using correctly sized factory locations, this step can be passed. A hole can be cut either with a pair of metal tin snips, an air or jig saw, or with a hole saw corresponding to the size of the midrange listed below. o 4-3/4" Hole Saw (5-1/4" woofer installation) o 5-5/8" Hole Saw (6-1/2" woofer installation) WARNING: Check for clearance of window mechanisms and electrical wires BEFORE you drill. Step 5: Run the speaker wire to the speakers. Make sure to keep wires away from sharp metal or other edges. When passing through metal, use a protective grommet. Step 6: Pre-drill mounting screw holes using a 1/8" drill bit. WARNING: Check for clearance of window mechanisms and electrical wires BEFORE you drill. Step 7: Pull the wire through the speaker opening and connect to the speaker. Be sure to observe proper mid/woofer polarity during this process. Step 8: Mount the speaker- Place the speaker and the grille in the installation hole. Align the mounting screw holes and drive in the four mounting screws. Flush MountTweeterAssemblyTweeterCupPressureRingTweeterWireFlush MountTrim RingWiringHarnessPanelWiringHarnessPanel Figure 3Figura 3Abbildung 3 Installing the Tweeter SURFACE MOUNTING Step 1: Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location. Step 2: Place the provided template or tweeter cup against the panel and mark the two holes at the rear of the housing. Step 3: Drill the smaller holes using a 1/8" drill bit. These are the mounting screw holes. WARNING: Check...
Este manual também é adequado para os modelos :altofalantes do carro e Subwoofers - CO552 (1.43 mb)
altofalantes do carro e Subwoofers - CO652 (1.43 mb)
altofalantes do carro e Subwoofers - CO652 (1.43 mb)