DO NOT CONNECT AMP OR ANY AUDIO SOURCE TO ILLUMINATION INPUTS AS DAMAGE TO LIGHTS WILL OCCUR. 10. Illumination connection: The positive (+) output from your 12V system connects to the positive (+) input, and the negative (ground) connects to the negative (-) input on the input cup located on the rear of the subwoofer enclosure. Improper 12V polarity will not cause damage to the lights, but they will not illuminate. XOBP12D GUIDELINES Enclosure Guidelines To achieve the best possible sound from t

The lighting features of all illuminite products require a 12 volt DC power source to operate. The speaker has two distinct sets of input terminals. The first is labeled audio input terminals and the second is labeled illuminite lighting inputs. The inputs are clearly marked with a label positioned directly above the terminal housing. The polarity (+ and -) indicators for each set of inputs also appear on these labels. 1. Do not connect amplifier or any audio source to illuminite lighting inputs

Although Dual has attempted to make sure all of the information contained within this manual is accurate, please be aware that any part of it is subject to change without notice. Safety This symbol is intended to alert the user to the presence of important instructions. Failure to heed these instructions can result in injury or unit damage. To prevent injury and damage to the unit, please read and follow the instructions in this manual. If you feel unsure about installing this system yourself, h

Make sure the area is large enough for the speaker to mount evenly. Also ensure the mounting location is deep enough for the speaker to fit. 2. Refer to the specification chart to determine the proper diameter hole to cut for your speaker model. 3. If supplied, use the plastic mounting ring as a template to mark the locations for the mounting screws. Drill the holes with a 3/32" bit. 4. Be sure to observe proper polarity when connecting the wires. The speaker's positive terminal is indicated wit

Failure to heed these instructions can result in injury or unit damage. To prevent injury and damage to the unit, please read and follow the instructions in this manual. If you feel unsure about installing this system yourself, have it installed by a qualified audio technician. Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury. DS SERIES INSTALLATION Installation The following installation instructions are very basic. If

Safety This symbol is intended to alert the user to the presence of important instructions. Failure to heed these instructions can result in injury or unit damage. To prevent injury and damage to the unit, please read and follow the instructions in this manual. If you feel unsure about installing this system yourself, have it installed by a qualified audio technician. Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury. DS

Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury. DS SERIES INSTALLATION Installation The following installation instructions are very basic. If you feel unsure about personally installing this speaker system, Dual recommends acquiring the services of a professional car audio installation center. Before installation, please follow these guidelines: 1. Be sure to carefully read and understand the instructions before attem

4. Use the highest quality connectors for a reliable installation and to minimize signal or power loss. 5. Use caution before you drill or cut! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle. 6. Never run speaker wires underneath your vehicle. Running speaker wires inside the vehicle provides the best protection from exhaust heat and environmental elements. 7. Avoid running wires over, near, or th

Safety This symbol is intended to alert the user to the presence of important instructions. Failure to heed these instructions can result in injury or unit damage. To prevent injury and damage to the unit, please read and follow the instructions in this manual. If you feel unsure about installing this system yourself, have it installed by a qualified audio technician. Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury. DS

5. Fit the speaker to the hole cut-out. Mount the speaker using the supplied screws. If the speaker grill is to be used, insert 4 screws into the grill holes and then mount the speaker. DS SERIES INSTALLATION Specifications MOUNTING HEIGHTTWEETER PROTRUSIONTOP-MOUNTING DEPTHBOTTOM-MOUNTING DEPTHCUT-OUT DIAMETER The diagram featured above is to be used in conjunction with the specifications matrix guide below: DS42 .38" 2.25" .25" 2.00" 3.63" 86 85Hz-20kHz 50 100 DS52 .44" 3.06" .31" 2.75" 4.56"