Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
REMOVABLE LINING 13. To remove the lining from the car seat, detach thehood. Unfasten the safety belt and slip it out ofthe sack at the back. 14. Slip the fastener tabs on the sack out from underthe car seat. 15. Slip the leg-divider belt buckle out of the openingin the sack. . The hood is made of plastic, and can be washedwithout being removed. INSTRUCTIONS FOR USE IN THE VEHICLE IMPORTANT: 16• The "Primo Viaggio" car seat can be fastenedto the front seat of a car that does not have an air bag system installed, or to the back seatof the car. The seat may be fastened usingonly three-point safety belts (see figure). It is forbidden to use a two-point or abdominalsafety belt to attach the child car seat, sincethese belts do not guarantee the child’s safety. FASTENING THE BASE TO THE VEHICLE 17. Place the base for the child car seat on the seat of the vehicle. Since not all vehicle seats slope atthe same angle, the height-adjustable base willallow you to keep the child car seat in the correctposition, parallel to the ground. . The position of the base is correct when the bubble on the gauge is completely visible. . To adjust the base, use one hand to turn knob A, and the other hand to push down on point B tosimulate the child.s weight. Adjust the base sothat the bubble is completely visible in the gauge. 18. Slip the vehicle seat belt through the two sideslots on the base, as shown in the figure. 19. Fasten the buckle to the vehicle seat, as shown inthe figure. 20. If your vehicle is equipped with a seat belt with afree-sliding buckle (like most modern vehicles), you must attach a Surefix Clip to it. Using aSurefix Clip guarantees correct attachment of thechild car seat to the base. . Remove the Surefix Clip from its housing, as shown in the figure. 21. Grab the vehicle shoulder strap (the free strap) just above the buckle, and hold it taut whileslipping the Surefix Clip onto the free strap, asshown in the figure. The Surefix Clip must holdthe strap taut. (Once the Surefix Clip has beenmounted correctly, it can be left on the vehicleseat belt to make it easier to fasten the base each time). 22. After mounting the Surefix Clip, check the tilt ofthe base again. If the bubble is not completelyvisible in the gauge, turn the knob again totighten the belt. . The base is ready for fastening the child car seatto it. FASTENING THE CHILD CAR SEAT TO THE BASE IN THE VEHICLE 23. Place your child in the child car seat, and fastenthe safety belt. . The car seat must be positioned backwards, inrelation to the direction of the vehicle. . Fasten the car seat to the base, pressing with both hands until it clicks into place. 24. With the child car seat mounted in the vehicle, thehandle on the seat must be lowered all the wayagainst the back of the vehicle seat, as shownin the figure. Push the handle until it clicks into place. 25. Pass the vehicle seat belt around the backrest of the child seat. 26. Slip the vehicle seat belt through the slot on theback of the seat, as shown in the figure. 27. Check to make sure that the seat belt is taut and securely fastened, for maximum safety. . To remove the child car seat from the vehicle, remove the vehicle seat belt from the back of the child seat. Pull the handle until it clicks into placein an upright position, and unfasten the childseat from its base. Leave the base mounted in the vehicle, ready for use. CLEANING & MAINTENANCE Your product requires only minimal maintenance. Cleaning and maintenance operations must beperformed only by adults. . Be sure to keep all moving parts clean, lubricatingthem with light oil if necessary. . Regularly clean the plastic parts with a damp cloth. Do not use solvents or similar products. . Brush the fabric parts to remove dust. . Do not use solvents or similar products to clean thepolystyrene bumper. . Protect the product against smog, water, rain andsnow. Continued and extended exposure to sunlightcan change the colours of many materials. . Store the product in a dry area. SAFETY ATTENTION . IMPORTANT WARNING: IT IS FORBIDDEN TO MOUNT THE CHILD CAR SEAT ON A SEAT WITH AN AIR BAG SYSTEM INSTALLED. . THIS GROUP 0+ CHILD SAFETY CAR SEAT MUST ALWAYS BE INSTALLED FACING BACKWARDS IN RELATION TO THE DIRECTION THE CAR TRAVELS. . ALWAYS USE THE CHILD CAR SEAT SAFETY BELTS, AND CHECK TO MAKE SURE THAT THE CHILD DOES NOT UNLATCH THE BELT BY HIMSELF. . THIS PRODUCT WAS NOT DESIGNED FOR CHILDREN TO SLEEP IN. . TO AVOID DANGER OF THE CHILD’S FALLING OUT OF THE CAR SEAT, THE SAFETY BELT MUST ALWAYS BEUSED TO FASTEN THE CHILD IN THE SEAT. . WHEN ATTACHING THE BASE AND THE CHILD CAR SEAT, PASS THE THREE-POINT CAR SEAT BELTTHROUGH THE SPECIAL SLITS. . THIS CAR SEAT MAY BE MOUNTED ON THE CAR USING ONLY THREE-POINT SAFETY BELTS. IT IS FORBIDDEN TO USE TWO-POINT OR ABDOMINAL BELTS TO FASTEN THE CHILD CAR SEAT (see theSafety Regulations). . NEVER REMOVE THE CHILD FROM THE SAFETY CAR SEAT WHILE THE CAR IS MOVING. . NEVER LEAVE YOUR CHILD ALONE IN THE CAR. . NEVER LEAVE TH...