Remove four (4) existing bolts A, B, C and D from side frame as shown in FIGURE 3. 5. Position scissor mechanism guard against the side frame with the folded edge down. Refer to FIGURE 3. 6. Align holes of scissor mechanism guard with holes on side frame. 7. Secure scissor mechanism guard to side frame with existing bolts A, B, C, and D. 8. Perform one (1) of the following: A. FOR MODEL 6905A BUILT BEFORE 04/01/2002 - Install new side panel with kit no. 1109705 and using instruction sheet no. 11

La languette se ver rouille dans l'orifice ES: Asegurese de que las lenguetas plasticas de las unidades de freno queden aseguradas en los agujeros de las patas traseras, como se muestra en el dibujo. 5 5 FR: Verifier que les languettes en plastique de l’essieu arriere se verrouillent dans les orifices des montants arriere, comme sur le schema ci-contre. Slide a wheel onto the axle than slide a washer onto the axle. ES: Deslize la rueda sobre el eje. Deslize la arandela sobre el eje. 6 6 FR: Fair

With the child seat fully reclined, open the belt shield at the back of the seat shell. Pull the yoke out from behind the seat and unhook one shoulder strap (dia 1d). Pull the cover from the top of the seat so that you can see the slots in the seat shell. Pull the shoulder strap through to the front of the seat. Handy tip – An alternative recline position may make the next step easier. Turn the chest pad tab sideways (dia 1e) and ease it through to the front of the seat . Then thread both straps

(Figure B). Step 5: Place Pad on seat and feed metal clips through the back 2 slots in the Pad, and then feed them through the slots in the booster seat (Figure C). Step 4: Be sure the clips are securely fastened under seat. Summer Infant, Inc. 582 Great Road PO Box 829 Slatersville, Rl 02876-0899 USA 1-800-268-6237 Summer Infant Europa« LTD. 20 Sparrows Herne Bushey, Hertfordshire WD231FXUK 44 (0)20 8420 4429 visit us at © 2005 Summer Infant, Inc. Colors and styles may vary. MADE IN CH

A rolled towel can be used on each side to support small children (fig. b). Be sure towels do not interfere with harness system. 2 3 Models 2 3 Models 2 3 3-PointModels 5-PointPLACING CHILD IN CAR SEAT (continued) (fig. a) (fig. b) OPERATIONS and ADJUSTMENTS 1 2-Piece Harness Tie: Buckle: • To open: Squeeze tabs and pull apart. 3-Point Models • To close: Snap halves together. Make sure harness tie is locked by pulling out on each half. • To buckle: Push tongue down into slot. Pull up on tongue t

P Modo de emprego/Garantia Verifique a lista de modelos de carros antes da instalacao! GB Instructions for use/Warranty Always check car fitting list before installation! F Mode d’emploi/Garantie Consultez toujours la liste des marques de voitures avant installation! D Gebrauchsanweisung/Garantie Bitte prufen Sie immer die Fahrzeugliste vor der Montage! NL Gebruiksaanwijzing/Garantie Controleer altijd eerst autotypelijst voor installatie! Contents 2 PrioriFix Instructions for use / Warranty 7 -

Selecting A Vehicle Seating Location........................................................................................7 • Vehicle Seat Belt Systems................................................................................................8 Section 7. Booster Car Seat Use...............................................................................................................9 Section 8. Additional Information • Certification........................................................

a). Thigh straps must also be snug (fig. b). Position Head Support (on certain models) in center of car seat with ends pointing down and snap into belt slots above harness straps (fig. c). 12 PLACING CHILD IN CAR SEAT - harness system (continued) Head Support (fig. a) (fig. b) (fig. c) 13 PLACING CHILD IN CAR SEAT - without harness system A WARNING To prevent serious injury or death: * Use ONLY the vehicles Lap/Shoulder Belt system when restraining the child in this booster seat. *

To make insertion of fabric easier, slide the upper and lower back pieces apart by squeezing the red adjustment 4 12 button. 4 5 Step 10. Attach backrest to base. “U”-shaped hooks on bottom of backrest will interlock with bars on base . Make sure that no part of the seat covering interferes when attaching backrest to the base. 13 5 Step 11. Once backrest is securely attached to the base, push backrest up as shown .6 6 14 Step 12. Your Graco booster seat is now ready to use. See page 21-27, “Usin

Store instruction manual inside pocket on back of car seat. © 2004 Combi USA, Inc. ACS0903c Combi USA • 1962 Hwy 160 West, #100 • Fort Mill, SC 29708 • Customer Service Telephone 1-800-992-6624 • Se Habla Español 1-803-548-6633 • Fax 1-803-548-3663 • • 10:00 a.m. - 5:00 p.m. Eastern Time • Monday - Friday C-Ombf instruction Manual Avatar™ Convertible Car Seat A WARNING A Correct installation and use can be a matter of Life or Death! Read and understand these instructions before using t