Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Please refer to them when you contact your AIWA dealer in case of difficulty. Model No. lADC-M55 Seria’ ‘0 ~ Welcome Thank you for your purchasing thw AIWA product. To optimize the performance of this unit, please read through this manual carefully. lTABLE OF CONTENTS nFEATU13ES Tracks from 6 CDs stored in the disc magazine can be selected and played. . Horizontal, vertical, slanted or suspended Installation can be made NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pmumt to Part 15 of the FCC Rules. These limits are designed to prowde reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radlofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determmed by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on circuit different from that to which the recewer IS connected. — Consult the dealer or an experienced radio/ TV technician for help. CAUTION Modifications oradjustmentsto this product, which are not expressly approved by the manufacturer, may void the user’s right or authority to operate this product. ENGLISH q PRECAUTIONS Do NOT install the unit in a location where it may be subjected to: — Direct sunlight or other sources of excessive heat — Fluid, rain or moisture — Excessive dirt or dust — Excesswe vibration This unit is designed to be operated on a 12-volt DC negative-ground electrical system only. Choose themounting location carefully so that the unit will not interfere with normal driving functions. Before making connections, dlsconnectthe@ termmal of the car battery to avoid short circuiting, Notes on CDs . A defective or soiled disc stored in the disc magazine can cause the sound to drop out during play. Always handle a disc by holding its inner and outer edges. @iii Do NOTtouchthe surface of the unlabeled side of the disc. Do NOT attach paper or tape etc. to a disc. . Do NOT expose the discs todirectsunhght or excessive heat. Clean the discs before inserting them into the disc magazine. Always clean a disc from the center outward with a cleaning cloth. There may be burrs left on the inner and outer edges of a brand-new disc. The burr may cause the malfunction of the unit or sound drop out. Topreventthese problems, ifthe burrleft on the disc, be sure to remove them with a ball point pen, etc. as illustrated. Ball-point pen Burr Burr @ Ball-point pen % NEVER usesolvents suchasbenzine oralcohol to clean a disc. . You cannot play an 8-cm (3-inch) CD — even with the specially designed adaptor. . Do not use irregular shape CDs (example: heart-shaped, octagonal ones). It may result in malfunction. Notes on the disc magazine . Do NOT leave the disc magazine in a place subject to excessive temperature or humidity. l Do NOTinsert more than one disc per slot. Do NOT drop the disc magazine. ENGLISH2 lUNPACKING Compact disc changer Compact disc magazine Connecting cable Q, /’%0 o e Supplied mounting kit for the compact disc changer The letters are keyed to those in the instructions. Use only the supplied mounting hardware for safe and secure installation. @ Brdckets (2 ea.) @ Washer screws @ Plate brackets @ Wing nuts (4 ea.) @(G2’ @ Double-back tape 0 ~;; ;Iamp @ Screw @ Lead clamp (large) (2 sets) // ‘)7 3 ENGLISH lINSTALLATIONS Precautions Select the mounting location very carefully, referring to the following points. . Make sure that there is no fuel tank, wiring or piping ontheothersideof the mounting surface. Make sure that the installation of the unit will not hinder the movement of the deck lid or interfere with the spare tire, etc. Use only the supplied mounting kit for safa and proper installation. Removing the transport screws Find the three transport screws at the bottom of the unit, which lock the unit’s mechanism during transport. Remove these screws before installation. Retain these screws and replace them in the original positions if the unit is transported for service or maintenance. @ 77 Mounting angle setting levers Be sure to change the position of both mounting angle setting levers according to the angle at which the unit is to be installed. Mounting angle setting levers I insert a pointed object such es e screw driver or ball-point pen, etc. into the low spot of the lever and slide the lever to the position from among H (horizontal), 45”, and V (vertical) positions. Notes Be sure to eject the disc magazine when you set the levers. l Be sure to set both lev...