Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
050205 Printed in Korea AVDINPC INTRODUCTION Features • 40 GB Hard Drive • 512 MB DDR RAM • • • • • • • • • • • • 2 AVDINPC PREPARATION Congratulations on your purchase of the Audiovox AVDINPC Mobile Multimedia DVD/CD/MP3/WMA personal computer. Please read all of the instructions before beginning the installation. Installation Requirements This unit is designed for installation in vehicles with an existing radio opening. In many cases, a special installation kit will be required to mount the computer to the dashboard. These kits are available at electronics supply stores and car stereo specialty shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but cannot locate one, call our customer support line at 1-800- 323- 4815. (U.S.A. and Canada only.) Tools and Supplies The following tools and supplies are needed to install the computer. • Torx type, flathead and Philips screwdrivers • Wire cutters and strippers • Tools to remove existing radio (screwdriver, socket wrench set or other tools) • Electrical tape • Crimping tool • Volt meter/ test light • Crimp connections • 18 gauge wire for power connections • 16- 18 gauge speaker wire Disconnect Battery Before you begin, disconnect the battery negative terminal (Figure 1) Toll-Free Installation Assistance If you require assistance, contact Technical Support at 1- 800- 323- 4815 from 8:30 a.m. to 7:00 p.m. EST Monday through Friday and from 9: 00 a.m. to 5: 00 p.m. EST on Saturday. (U.S.A. and Canada only. ) NOTE: If the AVDINPC is to be installed in a car equipped with an onboard drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation to avoid causing a short circuit. Figure 1: Battery Terminals 3 AVDINPC INSTALLATION The unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the computer to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of installation. 1. Remove the existing factory radio from the dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new computer. 2. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new computer. CAUTION: Do not exceed M5 X 6 MM screw size. Longer screws maytouch and damage components inside the chassis. 3. Place the computer in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections are secure and insulated with wire nuts or electrical tape. After completing the wiring connections, plug the connector into the mating socket on the rear of the chassis and turn the unit on to confirm operation (vehicle ignition switch must be “on”). If the unit does not operate, re-check all wiring until the problem is corrected. 4. Connect your monitor (purchased separately) and install any software/ drivers supplied with the monitor. Follow the instructions included with the monitor to mount the monitor in the vehicle. NOTE: A PS/2 mouse is required for installing any drivers during initial setup. DO NOT MOUNT the unit to the dashboard until initial setup iscomplete and software is installed. 5. Mount the new computer assembly to the dashboard or center console using the reverse procedure in step 1. CAUTION: For proper operation of the DVD player, the chassis must bemounted within 20° of horizontal. Make sure the unit is mounted within this limitation. Figure 2: ISO Installation 4 AVDINPC WIRING Wiring Connections 1. PS/2 Mouse 2. PS/2 Keyboard 3. VGA 4. LAN ( RJ- 45) 5. USB 1/USB 2 6. S-Video 7. RCA Video 8. Printer 9. COM Port 10. MIC In 11. Line Out 12. Line In 13. AC Adapter ( Purchased Separately) – Only use an AC adapter with the following specifications: Output – 12V, 4.3A; Input – 100- 240V~1.5A, 50/ 60Hz; Center pin (+) positive 14. Car Power Input 15. Power Supply 16. ILLUMINATION WIRE (yellow) 17. ACC POWER WIRE ( red) – Connect to a +12 volt circuit that is only live when the ignition is on. The best connection point is at the car’s fuse block at the “RADIO” or “ACCESSORY” identified terminals. 18. CONSTANT POWER WIRE (yellow) – Connect the 12V PLUS constant power wire to a live 12 volt wire in the vehicle. Before making a connection, check that the wire you intend to connect it to is always live, even when the car’s ignition is turned off. If a live wire is not found, route the wire to the car’s fuse block and connect it to a live circuit there. 19. GROUND WIRE (black) – Securely fasten the Ground wire to a grounded metal part of the car’s chassis. If you cannot find an existing bolt or screw to fasten it to, drill a hole in the metal and secure it w...