Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the optional remote start enable toggle switch to the OFF position. Valet mode can also be used. XT-42 LCD TRANSMITTER OPERATION: LCD REMOTE CONTROL TRANSMITTER: 8 Note: If the system is interfered by stronger radio frequency around, sources of high voltage electric power or such obstacles like tall buildings and so on, the transmission range may get shorter as the system uses low output powered frequency. BATTERY REPLACEMENT: A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the battery weakens a icon shall be displayed on the LCD screen. When the old battery is replaced with a new one, there will be beep sounds indicate the power is up. AAA Note: Press the button two times when the battery compartment is empty, and then insert the new battery. THE REMOTE LCD ICONS WITH FUNCTION: Door Lock Door Unlock Your vehicle Your vehicle doors are doors are unlocked locked. Start Mode Valet Mode Your vehicle is running All the function shall be temporarily on hold. 9 Remote Transmission You are transmitting the signal to control unit Trunk Release Trunk open. Trunk symbol only. Vibration Mode Remote Control vibrates when the system is triggered Power Save Mode Save the battery power In – Range Indicator You are within the remote control range. Low Battery You have to replace the battery of remote control. Ignition On Driver paging Someone is paging you in front of your vehicle. ** ** Press the valet switch in the vehicle with the Ignition OFF to page the driver carrying the XT-42 two-way remote control. PROGRAM MODE FOR LCD REMOTE CONTROL TRANSCEIVER: Press and hold all four remote control buttons simultaneously unit one long beep is heard. LCD Programming has now been entered. Transceiver Button System Function Remark Program Mode - Switching code for 2nd / 1st Car Operation Press within 5 seconds Program Mode - Melody / Vibration Mode Press within 5 seconds Program Mode - Power Save Mode Press within 5 seconds LCD screen lamp turns on for 5 seconds. -+ Clear the Flash Icon and Melody Sound Press within 3 seconds 1. Second Vehicle Security Operation: Your remote transmitter can be utilized to control a second vehicle’s Auto Page security system. To program the remote control transmitter to a second vehicle, follow the instructions for Transmitter programming. All programming parameters are the same except for the following: 10 For Regular Remote Control Transmitter: Regular Remote Control Transmitter: 1. Prior to pushing any button on the transmitter. Press the Select II button first on the standard transmitter. 2.Once II button is pressed the LED on the transmitter will illuminate for 3.5 seconds. While the LED is illuminated, press the button for the function you want to operate on the standard remote transmitter to control a second vehicle security system. For 2-way LCD Remote Control Transceiver: 2nd Car Operation: While the “II” icon display on the LCD screen, you can remote control and communicate with a second Autopage AM frequency security system. It has two short “beep” sounds while pressing any button of the LCD screen transceiver 1. Press and hold all four remote control buttons simultaneously unit one long beep is heard. LCD Programming has now been entered. 2. Within 5 seconds press and hold button until two beeping sounds are heard and the “II” icon will display on the LCD screen to indicate the second transceiver pin code has been initiated. 3. To exit programming mode, take no action for five seconds. The remote control will generate two long beeps to indicate programming mode has been exited. Back to first Car Operation: This will allow you to control and communicate with the first vehicles security system. 1. Press and hold all four remote control buttons simultaneously unit one long beep is heard. Programming has now been entered. 2. Within 5 seconds press and hold button until one beep sound is heard. 3. To exit programming mode, take no action for five seconds. The remote control will generate two long beeps to indicate programming mode has been exited. Vibration / Melody Mode: Vibration mode is useful when you are in a noisy place and it is difficult to hear the beep sound from the remote control. In this mode the unit will vibrate if your security system is triggered. 11 1. Press and hold all four remote control buttons simultaneously until one long beep is heard. Programming has now been entered. 2. Within 5 seconds, press the button to select the mode of vibration or melody, the icon will displayed on the LCD screen to show the LCD remote transceiver is in vibration mode. 3. To exit programming mode, take no action for five seconds. The remote control will generate two long beeps to indicate programming mode has been exited. Power Save Mode: While in the power save mode, the LCD remote transceiver will “sleep” until a button is pushed. This ...