Assessments - 4, GPA: 5 ( )

Fabricante : Pioneer Arquivo Tamanho: 2 mb Arquivo Nome : Língua de Ensino:

Fotos e especificações  Pioneer  DEH-2310UB

1 Press M.C. to turn the power save on or off. Using an AUX source 1 Insert the stereo mini plug into the AUX input jack. 2 Press S (SRC/OFF) to select AUX as the source. Note AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on the previous page. Sound muting Only for DEH-2300UB, DEH-2300UBB and DEH-2320UB. Sound is muted automatically when: ! A call is made or received using a cell phone connected to this unit. ! Voice guidance is output from a connected Pioneer navigation unit. The sound is turned off, MUTE is displayed and no audio adjustments, except volume control, are possible. Operation returns to normal when the phone connection or the voice guidance is ended. En Section Section 03 Installation Installation — Never band together negative cables of b Blue/white Connections Power cord multiple speakers. Connect to auto-antenna relay control term 03 English ! When installing this unit in a vehicle without through the blue/white cable. Connect this 1334245566b897aedc c Yellow/black an ACC (accessory) position on the ignition cable to the system remote control of an exter- Only for DEH-2300UB, DEH-2300UBB and Important ! When this unit is on, control signals are sent inal (max. 300 mA 12 V DC). switch, failure to connect the red cable to the nal power amp or the vehicle’s auto-antenna DEH-2320UB. terminal that detects operation of the ignition relay control terminal (max. 300 mA 12 V DC). If you use an equipment with Mute function, key may result in battery drain. If the vehicle is equipped with a glass anten wire this lead to the Audio Mute lead on that na, connect it to the antenna booster power equipment. If not, keep the Audio Mute lead supply terminal. free of any connections. ! Never connect the blue/white cable to the d Speaker leads ON START OFF power terminal of an external power amp. White: Front left + Also, never connect it to the power terminal of White/black: Front left * ACC position No ACC position the auto antenna. Doing so may result in bat- Gray: Front right + ! Use of this unit in conditions other than the tery drain or a malfunction. Gray/black: Front right * following could result in fire or malfunction. ! The black cable is ground. Ground cables for Green: Rear left + or subwoofer + — Vehicles with a 12-volt battery and negative this unit and other equipment (especially, Green/black: Rear left * or subwoofer * grounding. high-current products such as power amps) Violet: Rear right + or subwoofer + — Speakers with 50 W (output value) and 4 must be wired separately. If they are not, an Violet/black: Rear right * or subwoofer * ohm to 8 ohm (impedance value). accidental detachment may result in a fire or e ISO connector ! To prevent a short-circuit, overheating or mal function, be sure to follow the directions below. malfunction. In some vehicles, the ISO connector may be 1 To power cord input divided into two. In this case, be sure to con 2 Depending on the kind of vehicle, the function nect to both connectors. — Disconnect the negative terminal of the This unit of 3 and 5 may be different. In this case, be battery before installation. sure to connect 4 to 5 and 6 to 3. Notes 12 — Secure the wiring with cable clamps or adhesive tape. Wrap adhesive tape around Back-up (or accessory) 3 Yellow ! Change the initial setting of this unit. Refer to SW CONTROL (rear output and subwoofer set- wiring that comes into contact with metal 4 Yellow ting) on page 11. parts to protect the wiring. Connect to the constant 12 V supply terminal. The subwoofer output of this unit is monaural. — Place all cables away from moving parts, 34 5 5 Red ! When using a subwoofer of 70 W (2 .), be such as the gear shift and seat rails. Accessory (or back-up) sure to connect the subwoofer to the violet 1 Power cord input — Place all cables away from hot places, 6 Red and violet/black leads of this unit. Do not con- Connect to terminal controlled by ignition nect anything to the green and green/black 2 Rear output or subwoofer output such as near the heater outlet. 3 Antenna input — Do not connect the yellow cable to the bat- switch (12 V DC). leads. 4 Fuse (10 A) tery by passing it through the hole to the 7 Connect leads of the same color to each 5 Wired remote input engine compartment. other. — Cover any disconnected cable connectors Only for DEH-2300UB, DEH-2300UBB and Power amp (sold separately) 8 Black (chassis ground) DEH-2320UB. with insulating tape. 9 Blue/white Perform these connections when using the The pin position of the ISO connector will dif optional amplifier. Hard-wired remote control adaptor can be Do not shorten any cables. — connected (sold separately). — Never cut the insulation of the power cable of this unit in order to share the power fer depending on the type of vehicle. Connect 9 and b when Pin 5 is an antenna control .. 132455 with other devices. The current capacity of type. In another type of vehicle, never connect the cabl...

Baixe o seu

Para fazer o download, introduza 2 dígitos :