Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
3 Installation/Connection 4 Installation General notes • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring and make sure that the unit works properly. • Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. • Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop. • If installation angle exceeds 30° from horizontal, the unit may not perform properly. • Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration. Din Front/Rear-Mount This unit can be properly installed either from ‘Front’ (conventional DIN Front-mount) or ‘Rear’ (DIN Rear-mount installation, utilizing threaded screw Holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. 1. DIN front-mount (Method A) 1. Car dashboard 2. Sleeve 3. Screw 4. Nut (5 mm) 5. Spring washer 6. Screw (5 х 25 mm) 7. Metal strap 8. Flat washer 3 2 1 182 53 1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation. 2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place. 3. Use the metal strap to fix the rear side of the unit. Determine a place for fixing and install the strap as shown in the picture. You can bend the strap to the needed angle with your hands. 4. Make the necessary wire connections. Ensure the connections are correct. 5. Install the unit into the sleeve until the side locks are fixed. 1 3 5 4 6 8 7 Dismantling the unit a – Trim frame b – Frame uninstall direction c – Release key insertion Installation/Connection c b а 4. Vehicle dashboard. 5. Lock (remove this part). The outer trim frame and mounting sleeve are not used for method of installation. 2 2 5 5 4 3 1. Switch off the unit and detach the front panel. 2. Insert your fingers into the groove in the front side of the trim frame (apply some effort to detach the frame). Pull the frame to detach it. 3. Insert the supplied release keys into the both sides of the unit body to click, as shown in the picture. To extract the unit from the dashboard, pull the release keys or the unit body to pull it out. Before detaching the unit, ensure it is not fixed with the metal strap. Trim frame installation To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame. When the trim frame being installed, the side with the groove should face down and fixed first. 2. DIN rear-mount (Method B) For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factory radio mounting brackets. 1. Select a position in which the screw holes of the brackets (3) are aligned with the screw holes in the unit body, and screw in two screws (2) in each side. 2. Screw. 3. Factory radio mounting brackets. Detachable control panel Install the fastening hole on the right side of the front panel on the right fastening of the unit. Then install the fastening hole on the left side of the front panel on the left fastening of the unit. After that, lift the panel and press on the middle of the panel until a click. Ensure that the panel is properly fixed, otherwise error symbols may be displayed and some buttons may not function. To detach the front panel, press OPEN button and distract the left, then the right side of the panel from the fastenings of the unit. The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and the control panel is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc. If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel. Anti-theft system The front panel of this unit can be stored in the protective case and carried away when you leave the vehicle to deter theft. Switch off the power of the unit. Detach the front panel, then put it to the protective case and take it with you. 5 Installation/Connection 6 Connection Connection diagram ANTENNA SOCKET ORANGE TEL.MUTE ANTENNA CONTROL GROUND POWER B+ FRONT 4 ohm REAR 4 ohm LEFT SPEAKER TO CAR BATTERY MEMORY B+ BLUE YELLOW BLACK RED +12V WHITE WHITE/BLACK GREEN GREEN/BLACK FRONT RCA CONNECTOR LEFT = WHITE RIGHT = RED REAR RCA CONNE...